Miele PW 5065 manual Electrical connection

Page 52

Installation

Electrical connection

,This installation should be performed by an experienced and qualified technician, in accordance with local codes and regulations.

The washer comes with a power cord without a plug.

The machine is supplied as standard for connection to a 208 V, 60 Hz, 20 A, 2-phase electrical supply*.

For extra safety it is advisable to install a residual current device (RCD) with a trip current of 30 mA.

The machine must only be connected to the voltage and frequency shown on the data plate.

,*To convert the machine to another electrical connection, please read the converting manual on the wiring diagram inside the washer. The conversion must be performed by a Miele Service Technician. Additionally the "Heating level" setting must be adjusted.

,Do not install devices to automatically turn the washer off, i.e. a clock timer.

If the machine is hard wired, two 20 A circuit breakers must be provided on-site. Switches with a contact gap of more than 3 mm are valid as separators. All components must be CSA or UL approved.

52

Image 52

Contents Operating manual Washer Contents Important Safety Instructions Technical SafetyUse Using accessories ChildrenGuide to the washer Control panelDisplay with -, OK and + buttons Door buttonTemperature conversions Celsius Fahrenheit Display+ buttons OK buttonBefore using for the first time Setting time of dayReminder of the shipping struts First washSort the laundry Using the washerGeneral tips Load the laundry Close the drum doorSelect a program Delay StartPre-wash Too little detergent may cause Adding detergentToo much detergent may cause Starting a program At the end of a programCoin mechanism Remove the laundryCanceling a program Adjusting the temperatureAdjusting the spin speed Changing a programAdding/removing laundry during a wash program Drum door cannot be opened ifProgram guide Bed linen 60C to 40C 140F to 104F Curtains 40C to cold 104C to coldDenim 40C to cold 104C to cold Dark garments 40C to cold 104C to coldSpecial programs Quick wash 40C 104F Shirts 60C to 40C 140F to 104FStarch Pillows 95C to 40C 203F to 104FDo not use agents containing paraffin Proofing 40C to 30C 104F to 86FExtra Rinse Intensive Wash 60C to 40C 140F to 104F Flour 95C to 40C 203F to 104FGrease and fat 95C to 40C 203F to 104F Towels short 40C 104FTowels + 60C to 40C 140F to 104F Capes 30C 86FChem. Therm. Dis min 60C 140F HygieneProgram sequence Main wash Rinse SpinSymbols Special features in the program sequence Anti-creaseSelecting a spin speed Delay Start Setting the delay startStarting the delay start Changing the delay startDetergent Water hardnessWater softener Normal soilingFabric softener, liquid starch Dye removers / Fabric dyesCleaning the washer Cleaning and CareCleaning the detergent drawer Cleaning the inlet hose filters Cleaning the inlet hose filterCleaning the filter in the inlet valve Frequently asked questions Wash program cannot be startedDisplay shows a fault message Display message Possible cause SolutionGeneral problems with the washer Poor wash results Door will not open when the Door button is pressed Open the lint trap door Remove the toolMachines with a drain pump Remove the lint trap lid Open the drum doorMachines with a drain valve Changing the light bulb After sales service PC UpdateOptional accessories RepairsPage Installation Instructions Installation Front viewRear view Installation site InstallationRemoving the shipping struts Do not lift the washer by the drum doorInstallation Pull the shipping strut out Pull out the shipping strut outInstalling the shipping struts Leveling the washer Washer/ Dryer Stack Installation on a base Reinstallation of the machine lidCoin mechanism HeightMaintenance Water connectionCold water connection Extension hosesHot water connection Drain valve DrainageDrain pump Electrical connection Technical Data Disposal of the packing materials Help to protect the environmentDisposal of an old appliance Menu Settings J To adjust standard settings Settings J Accessing the Settings JLeaving the Settings menu Language JTime of day Display contrastDisplay brightness Selecting the clock displayStandby Not in current prog. factory defaultMemory Menu Settings Supervisor level Entering the codeAuto load control Supervisor levelMain wash water Rinse water Low Water PressureCottons water level Minimum Iron water levelMinimum Iron duration Special programs listPre-wash Cottons rinsesLeaving the Settings menu Minimum Iron rinsesExternal dosage Pre-rinse CottonsAlteration rights reserved