Amana RS3100007 service manual Pressure Switch, Rocker Switch, Graphic Panel, Loading Door

Page 19

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing.

Pressure Switch

1.Loosen control hood assembly, see “Control Hood Assembly” procedure steps 1 and 2.

2.Disconnect wires and plastic hose from pressure switch.

3.Remove screws securing pressure switch to control hood mounting plate.

4.Reverse procedure to reassemble.

NOTE: See appropriate wiring diagram when rewiring components.

NOTE: Before connecting hose to pressure switch, blow air through pressure hose to remove any condensation that may have accumulated in the hose.

Rocker Switch

1.Loosen control hood assembly, see “Control Hood Assembly” procedure steps 1 and 2.

2.Disconnect wire terminals from switch.

3.Squeeze plastic tabs located on top and bottom of switch and push switch out through the front of control panel.

4.Reverse procedure to reassemble.

Graphic Panel

1.Remove all knobs from switches.

2.Loosen control hood assembly, see “Control Hood Assembly” procedure steps 1 and 2.

3.Disconnect wires from components and carefully remove components from control hood assembly, see component removal procedure listed earlier.

4.Remove screws securing top cover to control mounting plate and remove top cover.

5.Remove screws securing end panels (each side) and remove end panels.

6.Remove grounding clip secured to metal tab on graphic panel.

7.Bend tabs on graphic panel (located inside of control hood) straight out towards the rear.

8.Remove graphic panel from front of control mounting plate.

9.Reverse procedure to reassemble.

NOTE: See appropriate wiring diagram when rewiring components.

Loading Door

1.Open loading door.

2.Remove screws securing left hinge to door and remove hinge.

Loading door

Hinge attaching screws

Hinge attaching screws

Hinge (right side)

Hinge (left side)

3.Raise loading door to a vertical position, disengage loading door from loading door clip by swing left side of door toward front of washer.

Loading

door

4. Rotate loading door so door is upside down.

19	RS3100007 Rev. 0

Image 19

Contents Top Load Washer ServiceTable of Contents Recognize Safety Symbols, Words, and Labels Important Notices for Consumers and ServicersImportant Information Important Safety Information Grounding Instructions General InformationModel Identification Proper Grounding and Polarization of 120 Volts Wall OutletsGeneral Operation Definition Component Test Procedure Results Component Testing InformationDiagram and Schematic for correct White Red Brown Internal Motor Diagram and SchematicWire harness Connection Block White Brown Yellow Red Blue BlueViolet Black White YellowBlue White/Black Motor Assembly Three speed motorNo warm water Possible Cause Result Troubleshooting ProceduresNo hot water Possible Cause Result No cold water Possible Cause ResultMotor does not operate Possible Cause Result Timer does not advance Possible Cause ResultConstant agitation Possible Cause Result No agitation Possible Cause ResultConstant spin Possible Cause Result Slow spin or no spin Possible Cause ResultPossible Cause Result Water leaking from outer tub Possible Cause Result Washer locks-up or binding Possible Cause ResultOuter tub does not empty Possible Cause Result Excessive vibration Possible Cause ResultControl Hood End Panels Disassembly ProceduresControl Hood Assembly TimerTemperature and Speed Switch Loading Door Pressure SwitchRocker Switch Graphic PanelAgitator Agitator, Drive Bell and Seal AssemblyInstalling Drive Bell Front Panel Service Access PanelMotor and Mounting Bracket Pump and Belt Removal Reassembly of Pump and BeltPump Mounting screws Rear Pump leg Assembly Embosses Motor AssemblyIdler Lever and Pulley Motor DisassemblyMotor Switch Motor Drive PulleyMixing Valve Door SwitchCabinet Top Washtub and Balance Ring Tub Cover and GasketOuter Tub Drive Pulley, Helix and Brake Weldment and Bearing Assembly Upper Bearing Assembly Transmission AssemblyFriction Ring Appendix a Installation Instructions Tub Wall Unit StandpipeProng grounded outlet only Positionwasher and LevelInstallation Summary Longer Water Inlet Hoses Adjustable leg Extension KitObserve all local codes and ordinances Siphon Break KitInstallation Requirements Appendix B Top Loading Washer Thank you for buying an Amana washer Recognize Safety Symbols, Words, LabelsImportant Safety Information Starting the Wash Close washer lid Starting the Wash contdWhat do the little numbers mean? CyclesDispensers Clean softener dispenser after each use. Remove dispenserFollow the Colors Features, Hints, and CareCold Storage and Non-Use Periods Moving and StorageTopic Possible Cause Solution Trouble ShootingWater Trouble Shooting contdRepairs resulting from the following Amana Washer WarrantyAppendix C Top Loading Washer ContentsRecognize Safety Symbols, Words, Labels Important Safety InformationSave Time and Money Asure Extended Service PlanParts and Accessories Important Information Thank you for buying an Amana washerElectrical Requirements Before You InstallWater Supply Requirements Risers Washer DimensionsLow Standpipe Installation LocationHOT Cold Wall Unit Questions?Warm/Cold Operating Instructions Washer Control PanelTo Wash Clothes Ex-Large FullOperating Instructions Bleach Dispenser Helpful Hints and FeaturesResetting Timer PausesGeneral Washer Care Care and CleaningSafety Spin Automatic Balance SystemTopic Possible Cause Solution Before Calling ServiceTopic Possible Cause Solution Vacations and Extended Non-Use Cold Storage and Non-Use PeriodsCold Weather Care Cold Weather StorageWarranty Provides For WarrantyOwner’s Responsibilities See manual for details Fast Track for Installing Washer