Amana RS3100007 service manual Starting the Wash

Page 41

Starting the Wash

If These Controls

are Different from

Yours

These controls are intended to show the variety of features that are available in the product line. If your washer does not have all the options that are shown, it is not a mistake. The information provided applies to several of the models in the product line.

1. Prepare clothes for washing

For best wash results:

•Remove items from pockets and cuffs

•Close zippers and fasteners; mend rips and tears

•Sort items into separate loads

•Pre-treat stains and heavily soiled areas

2.Select WASH/RINSE temperature

Always follow garment manufacturer’s care labels for each fabric. See chart below.

WASH / RINSE	TYPE OF CLOTHING

Hot/Cold	Sturdy whites and colorfast items;
	work clothes, soiled items, and cloth
	diapers

Warm/Warm	Delicate or colorfast items
Available on
some models
Warm/Cold −	Moderately soiled permanent press,
	silks, woolens, nylon, acrylic
	Rinsing of some items

Cold/Cold −	Non-colorfast items
	Extra-delicate clothing
	Rinsing of most items

NOTE: Energy Saver settings, marked with a dash (–), show temperature settings that use the least energy.

3. Select LOAD SIZE / WATER LEVEL

Variable control allows you to select the most appropriate setting for each wash load. Do not fill above top row of holes in tub with clothes. Use Water Level chart below to determine setting.

IMPORTANT: Do not hold knob at RESET for extended periods or washer flooding may result.

LOAD SIZE

WATER

LEVEL

QUICK WASH

Super Plus

Max. Fill

Large

3/4 – Full

Medium

1/2 – 3/4 Full

Small

1/2 Full

QUICK WASH

If you change your mind and the LOAD SIZE SETTING

If the tub is filling and you decide to change the LOAD SIZE SETTING, you must turn the knob to RESET before changing the load size. The tub can overfill if you do not turn to RESET first.

B–5	RS3100007 Rev. 0

Image 41

Contents Top Load Washer ServiceTable of Contents Important Information Important Notices for Consumers and ServicersRecognize Safety Symbols, Words, and Labels Important Safety Information Model Identification General InformationProper Grounding and Polarization of 120 Volts Wall Outlets Grounding InstructionsGeneral Operation Definition Component Test Procedure Results Component Testing InformationDiagram and Schematic for correct Wire harness Connection Block White Brown Yellow Red Blue Internal Motor Diagram and SchematicBlue White Red BrownViolet Black White YellowBlue White/Black Motor Assembly Three speed motorNo hot water Possible Cause Result Troubleshooting ProceduresNo cold water Possible Cause Result No warm water Possible Cause ResultMotor does not operate Possible Cause Result Timer does not advance Possible Cause ResultConstant agitation Possible Cause Result No agitation Possible Cause ResultPossible Cause Result Slow spin or no spin Possible Cause ResultConstant spin Possible Cause Result Outer tub does not empty Possible Cause Result Washer locks-up or binding Possible Cause ResultExcessive vibration Possible Cause Result Water leaking from outer tub Possible Cause ResultControl Hood Assembly Disassembly ProceduresTimer Control Hood End PanelsTemperature and Speed Switch Rocker Switch Pressure SwitchGraphic Panel Loading DoorAgitator Agitator, Drive Bell and Seal AssemblyInstalling Drive Bell Motor and Mounting Bracket Service Access PanelFront Panel Pump Mounting screws Rear Pump leg Assembly Reassembly of Pump and BeltEmbosses Motor Assembly Pump and Belt RemovalMotor Switch Motor DisassemblyMotor Drive Pulley Idler Lever and PulleyCabinet Top Door SwitchMixing Valve Outer Tub Tub Cover and GasketWashtub and Balance Ring Drive Pulley, Helix and Brake Weldment and Bearing Assembly Friction Ring Transmission AssemblyUpper Bearing Assembly Appendix a Installation Instructions Tub Wall Unit StandpipeProng grounded outlet only Positionwasher and LevelInstallation Summary Observe all local codes and ordinances Adjustable leg Extension KitSiphon Break Kit Longer Water Inlet HosesInstallation Requirements Appendix B Top Loading Washer Thank you for buying an Amana washer Recognize Safety Symbols, Words, LabelsImportant Safety Information Starting the Wash Close washer lid Starting the Wash contdWhat do the little numbers mean? CyclesDispensers Clean softener dispenser after each use. Remove dispenserFollow the Colors Features, Hints, and CareCold Storage and Non-Use Periods Moving and StorageTopic Possible Cause Solution Trouble ShootingWater Trouble Shooting contdRepairs resulting from the following Amana Washer WarrantyAppendix C Top Loading Washer ContentsRecognize Safety Symbols, Words, Labels Important Safety InformationParts and Accessories Asure Extended Service PlanImportant Information Thank you for buying an Amana washer Save Time and MoneyWater Supply Requirements Before You InstallElectrical Requirements Low Standpipe Installation Washer DimensionsLocation RisersHOT Cold Wall Unit Questions?To Wash Clothes Operating Instructions Washer Control PanelEx-Large Full Warm/ColdOperating Instructions Resetting Timer Helpful Hints and FeaturesPauses Bleach DispenserSafety Spin Care and CleaningAutomatic Balance System General Washer CareTopic Possible Cause Solution Before Calling ServiceTopic Possible Cause Solution Cold Weather Care Cold Storage and Non-Use PeriodsCold Weather Storage Vacations and Extended Non-UseOwner’s Responsibilities WarrantyWarranty Provides For See manual for details Fast Track for Installing Washer