Amana RS3100007 Before You Install, Electrical Requirements, Water Supply Requirements

Page 54

Before You Install

Electrical Requirements

Washer requires 120 volt, 15 amp, 60Hz power supply and 3-prong grounding plug. Refer to serial plate for specific requirements. Wiring diagram is located in control hood.

!WARNING

To avoid risk of personal injury or death due to electrical shock:

∙Observe all local codes and ordinances.

∙Disconnect electrical power to unit before servicing.

∙Ground appliance properly.

∙Check with a qualified electrician if you are not sure this appliance is properly grounded.

∙DO NOT ground to gas line.

∙DO NOT ground to cold water pipe if pipe is interrupted by plastic, non-metallic gaskets, or other insulating (non-conducting) materials.

∙DO NOT modify plug on power cord. If plug does not fit electrical outlet, have proper outlet installed by qualified electrician.

∙DO NOT have a fuse in the neutral or ground circuit. A fuse in the neutral or ground circuit could result in an electrical shock.

∙DO NOT use an extension cord with this appliance.

∙DO NOT use an adapter plug with this appliance.

∙DO NOT pinch power cord.

Grounding Instructions

For safety, washer must be grounded. All washer power supply cords are equipped with 3-prong grounding plug. Plug on cord must be plugged into appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify plug on washer cord. If plug will not fit outlet, have qualified electrician install proper outlet.

Do not remove warning tag from power cord.

!WARNING

To avoid risk of personal injury or death due to electrical shock:

∙Grounding wires and wires colored like grounding wires are NOT to be used as current carrying conductors.

∙Standard accepted color coding for ground wires is green or green with a yellow stripe.

Motor Overload Protector

Internal overload protector automatically stops motor in event of overload. Overload protector resets in approximately 3 minutes and motor automatically restarts. If overload protector stops motor again, quit using washer and call service technician.

Loading wash tub too full may result in motor overload. See Washing Guide for proper load size information.

Water Supply Requirements

!WARNING

Explosive hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. Before using washer, if hot water system has not been used for such a period, turn on all hot water faucets and let water flow for several minutes to release accumulated hydrogen gas. Hydrogen gas is flammable: do not smoke or use an open flame when flushing water lines.

Water supply faucets must fit standard 3/4" (19.05 mm) female garden hose couplings. Do not use slip-on or clamp-on connections.

NOTE: Water supply faucets should be easily accessible and turned off after extended use.

Optional longer inlet hoses are available at extra cost, if hoses supplied with washer are not long enough for installation. Order hoses as follows:

No. 20617 Inlet Hose, 8 feet (2.44 m)

No. 20618 Inlet Hose, 10 feet (3.05 m)

Cold water connection

Water supply

faucetsHot water connection

Water

Water mixing

inlet hoses

valve

Water Pressure

Static pressure measured at faucet must be 20–120 pounds per square inch (138 to 827 kPa). Water pressure under 20 pounds per square inch (138 kPa) results in extended washer fill time.

C–5

RS3100007 Rev. 0

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Service Top Load WasherTable of Contents Important Notices for Consumers and Servicers Recognize Safety Symbols, Words, and LabelsImportant Information Important Safety Information Proper Grounding and Polarization of 120 Volts Wall Outlets General InformationModel Identification Grounding InstructionsGeneral Operation Definition Component Testing Information Component Test Procedure ResultsDiagram and Schematic for correct Blue Internal Motor Diagram and SchematicWire harness Connection Block White Brown Yellow Red Blue White Red BrownViolet Motor Assembly Three speed motor Black White YellowBlue White/BlackNo cold water Possible Cause Result Troubleshooting ProceduresNo hot water Possible Cause Result No warm water Possible Cause ResultTimer does not advance Possible Cause Result Motor does not operate Possible Cause ResultNo agitation Possible Cause Result Constant agitation Possible Cause ResultSlow spin or no spin Possible Cause Result Constant spin Possible Cause ResultPossible Cause Result Excessive vibration Possible Cause Result Washer locks-up or binding Possible Cause ResultOuter tub does not empty Possible Cause Result Water leaking from outer tub Possible Cause ResultTimer Disassembly ProceduresControl Hood Assembly Control Hood End PanelsTemperature and Speed Switch Graphic Panel Pressure SwitchRocker Switch Loading DoorAgitator, Drive Bell and Seal Assembly AgitatorInstalling Drive Bell Service Access Panel Front PanelMotor and Mounting Bracket Embosses Motor Assembly Reassembly of Pump and BeltPump Mounting screws Rear Pump leg Assembly Pump and Belt RemovalMotor Drive Pulley Motor DisassemblyMotor Switch Idler Lever and PulleyDoor Switch Mixing ValveCabinet Top Tub Cover and Gasket Washtub and Balance RingOuter Tub Drive Pulley, Helix and Brake Weldment and Bearing Assembly Transmission Assembly Upper Bearing AssemblyFriction Ring Appendix a Installation Instructions Standpipe Tub Wall UnitPositionwasher and Level Prong grounded outlet onlyInstallation Summary Siphon Break Kit Adjustable leg Extension KitObserve all local codes and ordinances Longer Water Inlet HosesInstallation Requirements Appendix B Top Loading Washer Recognize Safety Symbols, Words, Labels Thank you for buying an Amana washerImportant Safety Information Starting the Wash Starting the Wash contd Close washer lidCycles What do the little numbers mean?Clean softener dispenser after each use. Remove dispenser DispensersFeatures, Hints, and Care Follow the ColorsMoving and Storage Cold Storage and Non-Use PeriodsTrouble Shooting Topic Possible Cause SolutionTrouble Shooting contd WaterAmana Washer Warranty Repairs resulting from the followingAppendix C Contents Top Loading WasherImportant Safety Information Recognize Safety Symbols, Words, LabelsImportant Information Thank you for buying an Amana washer Asure Extended Service PlanParts and Accessories Save Time and MoneyBefore You Install Electrical RequirementsWater Supply Requirements Location Washer DimensionsLow Standpipe Installation RisersHOT Cold Questions? Wall UnitEx-Large Full Operating Instructions Washer Control PanelTo Wash Clothes Warm/ColdOperating Instructions Pauses Helpful Hints and FeaturesResetting Timer Bleach DispenserAutomatic Balance System Care and CleaningSafety Spin General Washer CareBefore Calling Service Topic Possible Cause SolutionTopic Possible Cause Solution Cold Weather Storage Cold Storage and Non-Use PeriodsCold Weather Care Vacations and Extended Non-UseWarranty Warranty Provides ForOwner’s Responsibilities Fast Track for Installing Washer See manual for details
Top Page Image Contents