Amana RS3100007 service manual HOT Cold

Page 56

Parts

Supplied

2 flat rubber washers

HOT

COLD

2 screened hose filters

 

2 water fill hoses

 

 

beaded tie-down strap

 

4 rubber leveling foot pads

ToolsScrewdriver

Required

Level

Wrench

Pliers

 

STEP 1

 

 

Move

 

 

washer to

 

 

Instructions

 

 

final area

 

 

Remove

 

cardboard

shipping

 

base

plug and

 

 

Installation

 

 

save for

 

 

reuse

 

 

 

 

shipping

 

 

plug

1MOVE WASHER TO FINAL AREA; REMOVE SHIPPING PLUG

Washer must be within 4 feet of desired area before beginning installation. Open washer lid to remove styrofoam shipping brace from agitator. Remove installation parts from shipping brace for use.

NOTE: Save shipping plug; reinstall whenever washer is moved more than 4 feet. Do not lift or move washer without shipping materials in place.

When removing cardboard base panel under washer, plastic shipping plug is released from washer. Remove plug from cardboard base and save for reuse when moving washer.

2CONNECT WATER FILL HOSES TO WASHER Tightly push one flat rubber washer into one end of each water fill hose and attach this end of hose to washer. HOT and COLD connections are identified by letters H and C stamped into washer cabinet and by HOT and COLD printed on water fill hoses.

Tighten hose connections by hand until snug, then another

¼turn with pliers. DO NOT cross-thread or over-tighten couplings.

3CONNECT WATER FILL HOSES TO FAUCETS Before connecting hoses to water supply, turn on faucets and flush lines for approximately 2 minutes to remove foreign matter that could clog filter screens in water mixing valve or fill hoses.

Tightly push one screened filter washer onto remaining end of each water fill hose. Attach water hoses to HOT and COLD faucets. BE SURE HOT WATER HOSE IS

CONNECTED TO HOT WATER FAUCET.

Tighten hose connections by hand until snug, then another

¼turn with pliers. DO NOT cross-thread or over-tighten couplings. Turn on water and check for leaks. If leaks are found, retighten hose couplings. Continue tightening and rechecking until no leaks are found.

4SECURE DRAIN HOSE TO DRAIN

Remove drain hose from shipping position on rear of washer by unhooking hose from retainer clamp. Use beaded tie- down strap to secure “hook” end of drain hose to standpipe, wall inlet hoses, or laundry tub (must hold at least 20 gallons).

STEP 2

Push rubber washer into end of fill hose

HOT

COLD

 

Connect water fill hoses

to washer

STEP 3

Connect water fill hoses to faucets

faucet

screen filter

HOT

COLD

hose

 

 

RS3100007 Rev. 0

C–7

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Service Top Load WasherTable of Contents Important Information Important Notices for Consumers and ServicersRecognize Safety Symbols, Words, and Labels Important Safety Information General Information Model IdentificationProper Grounding and Polarization of 120 Volts Wall Outlets Grounding InstructionsGeneral Operation Definition Component Testing Information Component Test Procedure ResultsDiagram and Schematic for correct Internal Motor Diagram and Schematic Wire harness Connection Block White Brown Yellow Red BlueBlue White Red BrownViolet Motor Assembly Three speed motor Black White YellowBlue White/BlackTroubleshooting Procedures No hot water Possible Cause ResultNo cold water Possible Cause Result No warm water Possible Cause ResultTimer does not advance Possible Cause Result Motor does not operate Possible Cause ResultNo agitation Possible Cause Result Constant agitation Possible Cause ResultPossible Cause Result Slow spin or no spin Possible Cause ResultConstant spin Possible Cause Result Washer locks-up or binding Possible Cause Result Outer tub does not empty Possible Cause ResultExcessive vibration Possible Cause Result Water leaking from outer tub Possible Cause ResultDisassembly Procedures Control Hood AssemblyTimer Control Hood End PanelsTemperature and Speed Switch Pressure Switch Rocker SwitchGraphic Panel Loading DoorAgitator, Drive Bell and Seal Assembly AgitatorInstalling Drive Bell Motor and Mounting Bracket Service Access PanelFront Panel Reassembly of Pump and Belt Pump Mounting screws Rear Pump leg AssemblyEmbosses Motor Assembly Pump and Belt RemovalMotor Disassembly Motor SwitchMotor Drive Pulley Idler Lever and PulleyCabinet Top Door SwitchMixing Valve Outer Tub Tub Cover and GasketWashtub and Balance Ring Drive Pulley, Helix and Brake Weldment and Bearing Assembly Friction Ring Transmission AssemblyUpper Bearing Assembly Appendix a Installation Instructions Standpipe Tub Wall UnitPositionwasher and Level Prong grounded outlet onlyInstallation Summary Adjustable leg Extension Kit Observe all local codes and ordinancesSiphon Break Kit Longer Water Inlet HosesInstallation Requirements Appendix B Top Loading Washer Recognize Safety Symbols, Words, Labels Thank you for buying an Amana washerImportant Safety Information Starting the Wash Starting the Wash contd Close washer lidCycles What do the little numbers mean?Clean softener dispenser after each use. Remove dispenser DispensersFeatures, Hints, and Care Follow the ColorsMoving and Storage Cold Storage and Non-Use PeriodsTrouble Shooting Topic Possible Cause SolutionTrouble Shooting contd WaterAmana Washer Warranty Repairs resulting from the followingAppendix C Contents Top Loading WasherImportant Safety Information Recognize Safety Symbols, Words, LabelsAsure Extended Service Plan Parts and AccessoriesImportant Information Thank you for buying an Amana washer Save Time and MoneyWater Supply Requirements Before You InstallElectrical Requirements Washer Dimensions Low Standpipe InstallationLocation RisersHOT Cold Questions? Wall UnitOperating Instructions Washer Control Panel To Wash ClothesEx-Large Full Warm/ColdOperating Instructions Helpful Hints and Features Resetting TimerPauses Bleach DispenserCare and Cleaning Safety SpinAutomatic Balance System General Washer CareBefore Calling Service Topic Possible Cause SolutionTopic Possible Cause Solution Cold Storage and Non-Use Periods Cold Weather CareCold Weather Storage Vacations and Extended Non-UseOwner’s Responsibilities WarrantyWarranty Provides For Fast Track for Installing Washer See manual for details
Top Page Image Contents