JVC XR-D400SL manual Operation, To use the unit as a CD-R/RW drive, Press Scsi, Important notes

Page 30

Using as a CD -R/RW drive

Operation

1

2

3

4

5

6

7

8

9

10

OVER

POWER

POWER

11 12 13 14 15 16 17 18 19 20

SPEED	4x 2x 1x
REPEAT	1 TRACK ALL
			ERASE
		PROGRAM
	SPEED	REC	FINALIZE
	REPEAT
SOURCE			OPEN/CLOSE

SCSI

SCSI	AUTO REC	0 OPEN/CLOSE
	OPEN/CLOSE	0 OPEN/CLOSE
REC/PLAY

To use the unit as a CD-R/RW drive

1

2

3

Press POWER.
	POWER

Make sure the power indicator lights.

Press SCSI.

SCSI

Make sure the SCSI indicator lights up.

Turn on the host computer.

Important notes

•Setting the SCSI mode to OFF during using the unit as a CD-R/RW drive interferes with the operation of the host computer.

•Be sure to operate in the proper order as described above, or the unit cannot be recognized.

NOTES

•Your computer system and SCSI devices should not be set up in near proximity to a television or radio as they may cause interference with signal reception.

•Be careful not to set the same ID number to two SCSI devices attached to the same host computer.

•Be sure to turn off the power supply before changing SCSI ID numbers.

•When you have reset the ID number of a SCSI device, be sure also to reset the host computer.

•When the SCSI mode is set to OFF, the computer cannot recognize the unit.

•When you use the unit as a CD-R/RW drive, the audio functions (playback, recording) do not work.

26

Image 30

Contents XR-D400SL Introduction Einleitung1 Getting startedClass 1 Laser Product LASER-PRODUKT DER Klasse Achtung Disclaimer Table of contents IntroductionFeatures Supplied accessoriesSafety precautions Important cautionsPreliminary knowledge about discs For Audio useFor Scsi use CD-RW disc About recordable discsCD-R disc For audio recordingGetting started Names of parts and controlsFront panel Power button Track indicatorPower indicator REPEAT/SPEED indicators 14Rear panel AC power connectorTermination switch Line OUT jacks L/RTo connect the AC power cord Connections for audio useBefore making any connections Before operation Press PowerPlayback operations To turn on the unitOpen the loading tray by pressing To insert a discTo remove a disc Place the disc into the loading trayTo adjust the volume level Playing a CDTo play a CD To locate the beginning of a track To stop playback completely or temporarilyTo advance or reverse play rapidly while playing To locate a track directlyPlaying repeatedly Repeat Press Repeat repeatedly so that the ALL indicator lights upTo cancel repeat play To play the current track repeatedlyPress 6while pressing Track indicatorsTo create a program Repeat for more programming PressTo check the programmed tracks manually To cancel program playTo cancel a track To add a trackLimitations of recording Recording operationsBefore operations About FinalizeSpeed indicator Track indicators of the tracksRecording a disc Auto REC Press Auto REC To cancel recording during recordingPress Speed to select the recording speed 4x → 2x → 1x → 4x →Recording desired tracks Program REC To record desired tracksPress Program REC To cancel program recording during recording Repeat for more programmingTo check the programmed tracks automatically Finalize indicator Finalizing a disc FinalizeAbout Finalize Erasing the recorded data Erase System configuration Using as a CD-R/RW driveConnecting and setting ConnectingSetting the Scsi device ID number Host Computer With Scsi connector UnitAbout the Scsi daisy chain Press Scsi OperationTo use the unit as a CD-R/RW drive Turn on the host computerAdditional information Care and handling of discsTroubleshooting Symptom Possible case RemedyOFF Error messages Number Description Remedy Track indicatorScsi mode SpecificationsAudio mode GeneralEN. GE. FR 0400NHYUBNSAN