JVC XR-D400SL manual Specifications, Audio mode, Scsi mode, General

Page 35

Additional information

Specifications

Audio mode

Available discs

Source drive:	Audio CD (including an audio data of CD-EXTRA, CD
	TEXT, MIXED AUDIO DISC)
Rec/Play drive:	For recording and playback
	CD-R, CD-RW disc for audio use (1x – 4x Recording
	compatible, MAX. 79minutes*)
	For playback
	Audio CD, Recorded CD-R or CD-RW disc

English

Audio output

LINE OUT (pin jack): Frequency response: Signal-to-noise ratio:

Total harmonic distortion:

PHONE OUT:

2.0Vrms (10 k ohms) 20 Hz to 20 kHz

75 dB

Less than 0.05% (1 kHz)

0.24Vrms (32 ohms)

Recording speed

Auto recording, Program recording, Finalize:

	4x, 2x, 1x
Erase:	4x only

SCSI mode

Available discs:	CD-R, CD-RW disc and CD-R, CD-RW disc for audio use
	(1x – 4x Recording compatible, MAX. 79minutes*)
Interface:	SCSI-2
Connector:	D-sub 50p half-pitched connector
Terminator:	ON/OFF switch (on the rear panel)
Reading/writing speed:	Max. 24x (READ), Max. 4x (WRITE, CD-R/RW)
Data transfer rate:	5 MB/s (asynchronous mode)
	10 MB/s (synchronous mode)
Average access time:	140 ms
Buffer capacity:	2 MB
System supported:	Windows 98 (includes 2nd edition), Windows 95,
	Windows NT 4.0
System requirements:	Pentium MMX 166, 64 MB RAM equivalent or higher
(recommended)

*includes discs marked “80 minutes Disc” in general. (Note: You cannot use the SOURCE drive as the SCSI drive.)

Additional information

General

Power requirements:	AC 100 – 240 V	, 50/60 Hz
Rating current:	0.6 A
Mass:	4.6 kg
Dimensions (W x H x D):	190 x 234 x 265 mm

Specifications and appearance are subject to change without prior notice.

31

Image 35

Contents Introduction Einleitung1 Getting started XR-D400SLClass 1 Laser Product LASER-PRODUKT DER Klasse Achtung Disclaimer Introduction Table of contentsSupplied accessories FeaturesImportant cautions Safety precautionsFor Scsi use Preliminary knowledge about discsFor Audio use For audio recording About recordable discsCD-R disc CD-RW discFront panel Getting startedNames of parts and controls REPEAT/SPEED indicators 14 Track indicatorPower indicator Power buttonLine OUT jacks L/R AC power connectorTermination switch Rear panelBefore making any connections To connect the AC power cordConnections for audio use To turn on the unit Press PowerPlayback operations Before operationPlace the disc into the loading tray To insert a discTo remove a disc Open the loading tray by pressingTo play a CD To adjust the volume levelPlaying a CD To locate a track directly To stop playback completely or temporarilyTo advance or reverse play rapidly while playing To locate the beginning of a trackTo play the current track repeatedly Press Repeat repeatedly so that the ALL indicator lights upTo cancel repeat play Playing repeatedly RepeatRepeat for more programming Press Track indicatorsTo create a program Press 6while pressingTo add a track To cancel program playTo cancel a track To check the programmed tracks manuallyAbout Finalize Recording operationsBefore operations Limitations of recordingRecording a disc Auto REC Speed indicatorTrack indicators of the tracks 4x → 2x → 1x → 4x → To cancel recording during recordingPress Speed to select the recording speed Press Auto RECPress Program REC Recording desired tracks Program RECTo record desired tracks To check the programmed tracks automatically To cancel program recording during recordingRepeat for more programming About Finalize Finalize indicatorFinalizing a disc Finalize Erasing the recorded data Erase Connecting Using as a CD-R/RW driveConnecting and setting System configurationAbout the Scsi daisy chain Setting the Scsi device ID numberHost Computer With Scsi connector Unit Turn on the host computer OperationTo use the unit as a CD-R/RW drive Press ScsiCare and handling of discs Additional informationSymptom Possible case Remedy TroubleshootingOFF Number Description Remedy Track indicator Error messagesGeneral SpecificationsAudio mode Scsi modeEN. GE. FR 0400NHYUBNSAN