American Dryer Corp EURO-24 manual 26.1 mb, 14.92 29.9 mb

Page 29

2.Technical Gas Data a. Gas Specifications

 

 

TYPE OF GAS

 

 

 

 

 

 

 

NATURAL

LIQUID PROPANE

 

 

 

 

 

Manifold Pressure*

3.5 inches W.C.

8.7 mb

10.5 inches W.C.

26.1 mb

 

 

 

 

 

Inline Pressure

6.0 - 12.0 inches W.C.

14.92 - 29.9 mb

10.5 inches W.C.

26.1 mb

 

 

 

 

 

Shaded areas are stated in metric equivalents

 

 

 

*Measured at outlet side of gas valve pressure tap when gas valve is on.

b.Gas Connections

Inlet connection ------------ 1/2" inch N.P.T.

Inlet supply size ------------ 1/2" inch N.P.T. (minimum) Heat input (per dryer) --- 150,000 Btu/Hr (37,800 kcal/hr)

1)Natural Gas

Regulation is controlled by the dryer's gas valve's internal regulator. Incoming supply pressure must be consistent between a minimum of 6.0 inches and a maximum of 12.0 inches water column (W.C.) (15-30 mbar) pressure.

2)Liquid Propane (L.P.) Gas

Dryers made for use with L.P. gas have the gas valve's internal pressure regulator blocked open so that the gas pressure must be regulated upstream of the dryer. The pressure measured at each gas valve pressure tap must be a consistent 10.5 inches water column (26.2 mbar). There is no regulator or regulation provided in an L.P. dryer. The pressure must be regulated at the source (L.P. tank) or an external regulator must be added to each dryer.

 

 

 

 

 

 

TYPE OF GAS

 

L.P.

 

 

 

 

 

 

 

 

 

 

Conversion

ADC

BTU

 

 

Natural

 

 

Liquid Propane

kcal/hr

 

 

 

Kit

MODEL

Per Hour

Rating

Qty.

D.M.S.*

 

Part

Qty.

D.M.S.*

Part

Part Number

NUMBER

Rating

 

 

 

 

 

Number

 

 

Number

 

EURO-24

150,000

37,800

3

#29

 

140820

3

#46

140806

??????

 

 

 

 

 

 

 

 

 

 

 

Shaded area is stated in metric equivalent

* D.M.S. (Drill Material Size) equivalents are as follows:

Natural Gas

#29

= .1360" (3.4544 mm)

Liquid Propane Gas ..

#46

= .0810" (2.0574mm)

25

Image 29
Contents EURO-24 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Routine Maintenance Important Information SectionPersonal Injury or Fire could Result Safety PrecautionsStandards Specifications SpecificationsSpecifications UNPACKING/SETTING UP Installation ProceduresLocation Requirements Dryer Enclosure Requirements Fresh AIR Supply Exhaust Requirements Single Dryer Venting Illus. B Multiple Dryer Common Venting ILLUS. D Important Venting Reminders Electrical Information Must be Provided Black White Green Neutral Important a Circuit Serving Each Dryer Must be Provided Important a Circuit Serving Each Dryer Must be Provided EURO-24 GAS EURO-24 Steam Electrical Service Specifications PER DryerInjury and Improper Operation of the Dryer GAS Information14.92 29.9 mb 26.1 mbPage Page 862 KPa Steam InformationPage Compressed AIR Supply AIR Pressure Page Steam Damper Air Piston Flow Control Operation Adjustment Preparation for OPERATION/START-UP GAS Models only Preoperational TestsBasket Coating Preoperational InstructionsPage OPL Models Shut Down Instructions Parts SERVICE/PARTS InformationService Returning Warranty Cards Warranty InformationWarranty Returning Warranty PartsPage Cleaning Routine MaintenanceLubrication AdjustmentsLint Drawer Removal Drive motor not operating does not start TroubleshootingNo L.E.D. light emitting diode display Blower motor not operating does not start Microprocessor controller computer display reads door Microprocessor computer display reads dSFLPage Failed oven contactor/relay Failed heat selector switch Condensation on main door glass Dryer operates but is taking too long to dryExcessive noise and/or vibration Scraping noise from basket tumbler areaBlower motor only not operating Heating unit not operating ALL temperature selectionsDrive motor only not operating Dryer operates but is taking too long to dry load Heat unit not operating for only one 1 temperature selectionSail switch is fluttering for GAS and Electric Models only Data Label Technical InformationData Label Timing Legend Reversing Timer SPIN/DWELL AdjustmentsProcedure for Functional Check Replacement Components Page ADC 08/03/99-25 01/18/00-25 07/14/00-20