American Dryer Corp None Axial Thermistor Input, Thermistor Temp SET Point 100 to 400F, Coin Mode

Page 18

AXIAL THERMISTOR INPUT

This location determines whether the Phase 7 dual microprocessor controller (DMC) computer will use the thermistor probe to monitor the axial temperature in an axial dryer. This menu can be toggled ON and OFF. When the option is turned on, the Phase 7 DMC (computer) will be configured to an axial dryer.

NOTE: In an axial configuration, the new exhaust probe temperature range for drying cycles will be between 100°F and 150°F.

THERMISTOR TEMP SET POINT 100 TO 400°F

This location is only active when the AXIAL THERMISTOR INPUT has been turned ON. If the AXIAL THERMISTOR INPUT is OFF, this location will display NOT AVAILABLE. When the AXIAL THERMISTOR INPUT is ON, this location will determine at what temperature the Phase 7 DMC (computer) will cycle the heat, using the temperature reading from the thermistor probe.

PL #03 – HI KEY, PL #04 – MED KEY, PL #05 – LO KEY SETTINGS

TIME FOR AMOUNT TO START 1 TO 99 MINUTES

This location determines the time that is vended once the AMOUNT TO START is met. It is programmable from 1 minute to 99 minutes, in 1 minute increments. Each temperature setting has its own TIME FOR AMOUNT TO START so that each temperature setting can charge at a different rate.

Once the Phase 7 DMC (computer) is in Pause Mode and the Phase 7 DMC (computer) is displaying “CYCLE PAUSED” for Coin Mode or “CYCLE PAUSED...SELECT TEMP TO RESTART OR PAUSE TO CLEAR CYCLE” for Free Mode, the user can restart the dryer in HI, MED, or LO.

COIN MODE

In Coin Mode, when the Phase 7 DMC (computer) is set to Accumulative Time Mode and a cycle is started, the Phase 7 DMC (computer) will calculate how much time is available for the temperature selected by using the TIME FOR AMOUNT TO START for the temperature key selected and the AMOUNT TO START. If the Phase 7 DMC (computer) is paused and a new temperature key is selected the Phase 7 DMC (computer) will calculate how much time is left in the cycle for the new temperature selected. These calculations are based on the TIME FOR AMOUNT TO START for the new temperature key and the amount of credit that was available at the time the Phase 7 DMC (computer) was placed into Pause Mode.

FREE MODE

In Free Mode the Phase 7 DMC (computer) will use the TIME FOR AMOUNT TO START for the temperature key selected to determine how much time is available for the cycle started.

When the Phase 7 DMC (computer) is placed into Pause Mode, the Phase 7 DMC (computer) will calculate a ratio of how much time was left in the cycle at the time the Phase 7 DMC (computer) was placed into Pause Mode and the TIME FOR AMOUNT TO START for the temperature key that was previously selected. Once this ratio is determined, the Phase 7 DMC (computer) will use the same ratio to determine how much time is left in the cycle, when a new temperature key is selected. The Phase 7 DMC (computer) will multiply the TIME FOR AMOUNT TO START for the new temperature key by the ratio and that will determine how much time is left in the cycle.

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DMC Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Coin Mode Free ModeHOT Keys Pause Mode Scrolling RateRPM Clearing CREDIT/CLEARING Cycle Accessing Coin VaultClearing Fault Records and Credit Wrinkle GuardA.F.E. System D. Operating Messages Messages Common to Coin and Free Modes Select Temp to StartClose Lint Access Select Language Select Buzzer ModeSelect DRY Mode Select Temp ScalePause Time 0 to 3 Minutes Select Rotation Sensor ModeEnter Lint Cleaning Frequency 0 to 10 Hours Ready PromptAxial Thermistor Input Coin ModeFree Mode Thermistor Temp SET Point 100 to 400FEnter High DRY Temp 100 to 190F Currency SymbolTime for TOP OFF 1 to 99 Minutes Cool Time 0 to 9 MinutesSelect Vending Mode Accumulative TimeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Faults Select Vending SafeguardNo Faults Enter LEFT/RIGHT Coin Denomination 0.05 toProgramming Instructions Introduction to ProgrammingProgram Location Summary Programming Flowcharts MEDFlowchart Table of Contents Selecting Display Language Program ModeControl Settings Select Language English Spanish Temp Scale READY, InsertControl Settings Select Language Select Temp Scale Select Buzzer ModeSelecting Temp Scale OFF Selecting Buzzer ModeControl Settings Select Language Buzzer Mode CountControl Settings Select Language Beep Count 1 to 9 Beeps Select DRY ModeSelecting Beep Count Select Pause Time 0 to Selecting DRY ModeFree DRY Mode MinutesSelecting Pause Time Select Language Pause Time 0 to Minutes Select Ready PromptSelecting Ready Prompt ReadyMachine Electric Single Motor Machine Settings Select Model Type GAS Single MotorSelecting Model Type RotationSetting Rotation Sensor Lint Cleaning Frequency 0 to Hours Setting Lint Cleaning FrequencySettings Axial MachineTemp Setpoint Setting Axial Thermistor InputOFF Axial Thermistor InputSetting Thermistor Temp SET Point Thermistor TempHI KEY- Setting Time for Amount to Start HI KEY- Setting Time for TOP OFF Time for TOPTime for TOP OFF To 99 Minutes Time for Amount to Start 1 to Minutes HI KEY- Setting DRY Temp 100 to 190 FPL #03 HI KEY Settings Cool Time 0 to MinutesHI KEY- Setting Cool Time 0 to 9 Minutes PL#04 MED KEY SettingsPL #04 MED KEY Settings MED KEY- Setting Time for Amount to StartPL #01 Control Settings Time for Amount to Start 1 to MinutesMED KEY- Setting Time for TOP OFF MED KEY- Setting DRY Temp 100 to 190 F Cool Time 0 to MinutesMED KEY- Setting Cool Time 0 to 9 Minutes PL #05 LO KEY SettingsLO KEY- Setting Time for Amount to Start LO KEY- Setting Time for TOP OFF Time for TOP OFF To 99 MinutesLO KEY- Setting DRY Temp 100 to 190 F LO KEY- Setting Cool Time 0 to 9 Minutes PL #06 Vending ParametersSelecting Currency Symbol Vending ModeSelecting Vending Mode Selecting Vending Safeguard Setting Left Coin Denomination Control Settings PL #06 VendingSetting Right Coin Denomination Amount to Start 0.05 toSetting Amount to Start Amount forTOP OFF 0.05 to Setting Amount for TOP OFF 0.05 to PL#07 Fault RecordingAmount for TOP OFF PL #07 Fault Recording Accessing Upper Dryer Fault RecordsPL #01 Control Settings Upper Dryer FaultsAccessing Lower Dryer Fault Records PL #01 Control Settings PL #07 Fault RecordingLower Dryer Faults Flowchart for Clearing Credit Accessing and Clearing Coin Vault Total YESMED KEY Settings Factory DefaultsHI KEY Settings LO KEY SettingsControl Settings Language Fault Recording READY-INSERT Amount to StartUSD Diagnostic L.C.D. Fault Messages Error MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Drive Green L.E.D FAN Green L.E.D FSS Green L.E.DLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08
Top Page Image Contents