American Dryer Corp None user manual Select Vending Mode, Accumulative Time

Page 20

NOTE: Any time the Currency Symbol menu is accessed, the Phase 7 dual microprocessor controller (DMC) computer will clear any credit available on the Phase 7 DMC (computer) and will also reset the coin vault total.

SELECT VENDING MODE

The Vending Mode determines how the Phase 7 DMC (computer) will vend time to a customer when a coin is inserted into the dryer. The Phase 7 DMC (computer) uses this parameter to determine whether the Phase 7 DMC (computer) is in Accumulative Time or Accumulative Coin Mode. Depending on which mode the Phase 7 DMC (computer) is in, it will use a combination of the following program locations to determine how much time will be vended to the customer.

PL #03, PL #04, PL #05 – TIME FOR AMOUNT TO START

PL #06 – LEFT COIN DENOMINATION

PL #06 – RIGHT COIN DENOMINATION

PL #06 – AMOUNT TO START

PL #06 – AMOUNT FOR TOP OFF

ACCUMULATIVE TIME

In Accumulative Time Mode, after the initial AMOUNT TO START (PL #06) has been met, each additional coin afterward will have a specific value in time, which is determined by TIME FOR AMOUNT TO START (PL #03, PL #04, or PL #05) and AMOUNT TO START (PL #06).

Single Coin Acceptor

Example No. 1: If the dryer is equipped with a 25¢ coin acceptor and the AMOUNT TO START (PL #06) is 25¢, the HI key TIME FOR AMOUNT TO START (PL #03) is 30 minutes. Each coin entered into the dryer will yield 30 minutes.

Settings: PL #06 (LEFT COIN DENOMINATION)	25
PL #03 (TIME FOR AMOUNT TO START)	30
PL #06 (AMOUNT TO START)	25

Formula: (LEFT COIN DENOMINATION [PL #06] / AMOUNT TO START [PL #06]) (TIME FOR AMOUNT TO START [PL #03]) = Vended Time (25¢/25¢)(30) = 30 minutes

Example No. 2: If the dryer is equipped with a 25¢ coin acceptor and the AMOUNT TO START (PL #06) is 50¢, the MED key TIME FOR AMOUNT TO START (PL #04) is 30 minutes. The insertion of the first two (2) coins into the dryer will yield 30 minutes; each additional coin entered into the dryer will yield 15 minutes.

Settings: PL #06 (LEFT COIN DENOMINATION)	25
PL #04 (TIME FOR AMOUNT TO START)	30
PL #06 (AMOUNT TO START)	50

Formula: (LEFT COIN DENOMINATION [PL #06] / AMOUNT TO START [PL #06]) (TIME FOR AMOUNT TO START [PL # 04]) = Vended Time (50¢/50¢)(30) = 30 minutes

(25¢/50¢)(30) = 15 minutes

18

Image 20

Contents DMC Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Coin Mode Free ModeHOT Keys RPM Pause ModeScrolling Rate Accessing Coin Vault Clearing Fault Records and CreditClearing CREDIT/CLEARING Cycle Wrinkle GuardA.F.E. System D. Operating Messages Messages Common to Coin and Free Modes Select Temp to StartClose Lint Access Select Buzzer Mode Select DRY ModeSelect Language Select Temp ScaleSelect Rotation Sensor Mode Enter Lint Cleaning Frequency 0 to 10 HoursPause Time 0 to 3 Minutes Ready PromptCoin Mode Free ModeAxial Thermistor Input Thermistor Temp SET Point 100 to 400FCurrency Symbol Time for TOP OFF 1 to 99 MinutesEnter High DRY Temp 100 to 190F Cool Time 0 to 9 MinutesSelect Vending Mode Accumulative TimeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Select Vending Safeguard No FaultsFaults Enter LEFT/RIGHT Coin Denomination 0.05 toProgramming Instructions Introduction to ProgrammingProgram Location Summary Programming Flowcharts MEDFlowchart Table of Contents Program Mode Control Settings Select Language English Spanish Temp ScaleSelecting Display Language READY, InsertSelecting Temp Scale Control SettingsSelect Language Select Temp Scale Select Buzzer Mode Selecting Buzzer Mode Control Settings Select Language Buzzer ModeOFF CountSelecting Beep Count Control Settings Select Language Beep Count 1 to 9 BeepsSelect DRY Mode Selecting DRY Mode Free DRY ModeSelect Pause Time 0 to MinutesSelecting Pause Time Select Language Pause Time 0 to Minutes Select Ready PromptMachine Selecting Ready PromptReady Machine Settings Select Model Type GAS Single Motor Selecting Model TypeElectric Single Motor RotationSetting Rotation Sensor Setting Lint Cleaning Frequency Settings AxialLint Cleaning Frequency 0 to Hours MachineSetting Axial Thermistor Input OFFTemp Setpoint Axial Thermistor InputSetting Thermistor Temp SET Point Thermistor TempHI KEY- Setting Time for Amount to Start Time for TOP OFF To 99 Minutes HI KEY- Setting Time for TOP OFFTime for TOP HI KEY- Setting DRY Temp 100 to 190 F PL #03 HI KEY SettingsTime for Amount to Start 1 to Minutes Cool Time 0 to MinutesHI KEY- Setting Cool Time 0 to 9 Minutes PL#04 MED KEY SettingsMED KEY- Setting Time for Amount to Start PL #01 Control SettingsPL #04 MED KEY Settings Time for Amount to Start 1 to MinutesMED KEY- Setting Time for TOP OFF MED KEY- Setting DRY Temp 100 to 190 F Cool Time 0 to MinutesMED KEY- Setting Cool Time 0 to 9 Minutes PL #05 LO KEY SettingsLO KEY- Setting Time for Amount to Start LO KEY- Setting Time for TOP OFF Time for TOP OFF To 99 MinutesLO KEY- Setting DRY Temp 100 to 190 F LO KEY- Setting Cool Time 0 to 9 Minutes PL #06 Vending ParametersSelecting Currency Symbol Vending ModeSelecting Vending Mode Selecting Vending Safeguard Setting Left Coin Denomination Control Settings PL #06 VendingSetting Right Coin Denomination Amount to Start 0.05 toTOP OFF 0.05 to Setting Amount to StartAmount for Amount for TOP OFF Setting Amount for TOP OFF 0.05 toPL#07 Fault Recording Accessing Upper Dryer Fault Records PL #01 Control SettingsPL #07 Fault Recording Upper Dryer FaultsLower Dryer Faults Accessing Lower Dryer Fault RecordsPL #01 Control Settings PL #07 Fault Recording Flowchart for Clearing Credit Accessing and Clearing Coin Vault Total YESFactory Defaults HI KEY SettingsMED KEY Settings LO KEY SettingsControl Settings Language USD Fault RecordingREADY-INSERT Amount to Start Standards Diagnostic L.C.D. Fault MessagesError Messages Page Page Page A.F.E. System Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Drive Green L.E.D FAN Green L.E.D FSS Green L.E.DLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08