American Dryer Corp None user manual INPUT/OUTPUT I/O Board L.E.D. Indicators

Page 72

C. INPUT/OUTPUT (I/O) BOARD L.E.D. INDICATORS

1.Top Pocket Inputs H2O – (RED L.E.D.)

LINT – (RED L.E.D.)

EXHL – (RED L.E.D.)

SAIL – (RED L.E.D.)

GAS_V – (RED L.E.D.)

MAIN – (RED L.E.D.)

FUSE – (RED L.E.D.)

BRHL – (RED L.E.D.)

2.Top Pocket Outputs HEAT – (GREEN L.E.D.)

DRIVE – (GREEN L.E.D.)

FAN – (GREEN L.E.D.)

FSS – (GREEN L.E.D.)

This light emitting diode (L.E.D.) will indicate the status of the water pressure sensor. If the water pressure is present, the L.E.D. will be ON.

This L.E.D. will indicate the status of the lint drawer. If the drawer is closed, then the L.E.D. is ON.

This L.E.D. will indicate the status of the exhaust high limit disk. If the disk is closed (temperature below 225º F [107º C]), then the L.E.D. is ON.

This L.E.D. will indicate the status of the sail switch. If the switch is closed, then the L.E.D. is ON.

This L.E.D. will indicate the status of the gas valve. If the gas valve is open (ON), then the L.E.D. is ON.

This L.E.D. will indicate the status of the main door. If the door is closed, then the L.E.D. is ON.

This L.E.D. should be on at ALL times. If L.E.D. is off this will indicate that fuse # F1 is blown.

This L.E.D. will indicate the status of the burner high limit disk. If the disk is closed (temperature below 330º F [166º C]), then the L.E.D. is ON.

This L.E.D. will indicate the status of the heat output. If the request to turn on the heater is made, then the L.E.D. is ON.

This L.E.D. will indicate the status of the basket (tumbler) forward direction output. If the request to tumble the basket (tumbler) in the forward direction is made, then the L.E.D. is ON.

This L.E.D. will indicate the status of the fan output. If the request to turn on the fan (blower) is made, then the L.E.D. is ON.

This L.E.D. will indicate that the S.A.F.E. system is active.

70

Image 72

Contents DMC Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Coin Mode Free ModeHOT Keys Pause Mode Scrolling RateRPM Accessing Coin Vault Clearing Fault Records and CreditClearing CREDIT/CLEARING Cycle Wrinkle GuardA.F.E. System D. Operating Messages Messages Common to Coin and Free Modes Select Temp to StartClose Lint Access Select Buzzer Mode Select DRY ModeSelect Language Select Temp ScaleSelect Rotation Sensor Mode Enter Lint Cleaning Frequency 0 to 10 HoursPause Time 0 to 3 Minutes Ready PromptCoin Mode Free ModeAxial Thermistor Input Thermistor Temp SET Point 100 to 400FCurrency Symbol Time for TOP OFF 1 to 99 MinutesEnter High DRY Temp 100 to 190F Cool Time 0 to 9 MinutesSelect Vending Mode Accumulative TimeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Select Vending Safeguard No FaultsFaults Enter LEFT/RIGHT Coin Denomination 0.05 toProgramming Instructions Introduction to ProgrammingProgram Location Summary Programming Flowcharts MEDFlowchart Table of Contents Program Mode Control Settings Select Language English Spanish Temp ScaleSelecting Display Language READY, InsertControl Settings Select Language Select Temp Scale Select Buzzer ModeSelecting Temp Scale Selecting Buzzer Mode Control Settings Select Language Buzzer ModeOFF CountControl Settings Select Language Beep Count 1 to 9 Beeps Select DRY ModeSelecting Beep Count Selecting DRY Mode Free DRY ModeSelect Pause Time 0 to MinutesSelecting Pause Time Select Language Pause Time 0 to Minutes Select Ready PromptSelecting Ready Prompt ReadyMachine Machine Settings Select Model Type GAS Single Motor Selecting Model TypeElectric Single Motor RotationSetting Rotation Sensor Setting Lint Cleaning Frequency Settings AxialLint Cleaning Frequency 0 to Hours MachineSetting Axial Thermistor Input OFFTemp Setpoint Axial Thermistor InputSetting Thermistor Temp SET Point Thermistor TempHI KEY- Setting Time for Amount to Start HI KEY- Setting Time for TOP OFF Time for TOPTime for TOP OFF To 99 Minutes HI KEY- Setting DRY Temp 100 to 190 F PL #03 HI KEY SettingsTime for Amount to Start 1 to Minutes Cool Time 0 to MinutesHI KEY- Setting Cool Time 0 to 9 Minutes PL#04 MED KEY SettingsMED KEY- Setting Time for Amount to Start PL #01 Control SettingsPL #04 MED KEY Settings Time for Amount to Start 1 to MinutesMED KEY- Setting Time for TOP OFF MED KEY- Setting DRY Temp 100 to 190 F Cool Time 0 to MinutesMED KEY- Setting Cool Time 0 to 9 Minutes PL #05 LO KEY SettingsLO KEY- Setting Time for Amount to Start LO KEY- Setting Time for TOP OFF Time for TOP OFF To 99 MinutesLO KEY- Setting DRY Temp 100 to 190 F LO KEY- Setting Cool Time 0 to 9 Minutes PL #06 Vending ParametersSelecting Currency Symbol Vending ModeSelecting Vending Mode Selecting Vending Safeguard Setting Left Coin Denomination Control Settings PL #06 VendingSetting Right Coin Denomination Amount to Start 0.05 toSetting Amount to Start Amount forTOP OFF 0.05 to Setting Amount for TOP OFF 0.05 to PL#07 Fault RecordingAmount for TOP OFF Accessing Upper Dryer Fault Records PL #01 Control SettingsPL #07 Fault Recording Upper Dryer FaultsAccessing Lower Dryer Fault Records PL #01 Control Settings PL #07 Fault RecordingLower Dryer Faults Flowchart for Clearing Credit Accessing and Clearing Coin Vault Total YESFactory Defaults HI KEY SettingsMED KEY Settings LO KEY SettingsControl Settings Language Fault Recording READY-INSERT Amount to StartUSD Diagnostic L.C.D. Fault Messages Error MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Drive Green L.E.D FAN Green L.E.D FSS Green L.E.DLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08