American Dryer Corp None user manual Diagnostic L.C.D. Fault Messages, Standards, Error Messages

Page 67

SECTION VIII

PHASE 7 DUAL MICROPROCESSOR CONTROLLER (DMC)

COMPUTER SYSTEM DIAGNOSTICS

IMPORTANT: YOU MUST DISCONNECTAND LOCK OUT THE ELECTRIC SUPPLY AND THE GAS OR STEAM SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE MACHINE, TO ALLOWACCESS FOR CLEANING,ADJUSTING, INSTALLATION, OR TESTING OFANY EQUIPMENT PER OSHA (Occupational Safety and HealthAdministration)

STANDARDS.

ALL major circuits, including the door, the microprocessor temperature sensor, and the heat and motor circuits are monitored. The Phase 7 dual microprocessor controller (DMC) computer will inform the user via the liquid crystal display (L.C.D.) of certain failure messages, along with light emitting diode (L.E.D.) indicators on the Inputs/Outputs (I/O) on the Phase 7 DMC (computer) board.

ERROR MESSAGES:

NOTE: Any error associated with the “Out of Order” message can be identified by pressing the “LO” key while in the “Out of Order” condition. If the “HI” key is pressed during this time, the remaining credit can be viewed. Any “Out of Order” message is immediately followed by a 3-second tone. If the fault has been corrected, holding the “PAUSE” key for 3-seconds will clear the fault message. If more than one (1) fault occurred at the same time after the first fault is cleared, the next fault will be displayed and will need to be cleared. This will occur until ALL faults have been displayed. In Free Mode, the Phase 7 DMC (computer) will not display “Out of Order”; it will just display the fault.

A. DIAGNOSTIC L.C.D. FAULT MESSAGES

MODEL FAULT – This routine monitors the inputs, such as the sail switch and gas valve, to determine the type of dryer the Phase 7 DMC (computer) is. Steam dryers DO NOT use a sail switch or valve input, and an electric dryer will not use a gas valve input. These signals allow the Phase 7 DMC (computer) to interpret what type of dryer it is controlling. The Phase 7 DMC (computer) determines what the expected dryer responses should be for that specific heat-type dryer. Anytime a model fault is detected, the Phase 7 DMC (computer) will interrupt the cycle and will display “MODEL FAULT” and will go into a Fault Mode with a brief audio indication. If the basket (tumbler) temperature is above 100°F (38°C) at the time of the failure, the Phase 7 DMC (computer) will continue to display “MODEL FAULT” while the dryer cools by running with no heat for 3 minutes or until the temperature drops below 100°F (38°C). Once the basket (tumbler) temperature is below 100°F (38°C), or the 3 minutes expire, the Phase 7 DMC (computer) will shut off ALL outputs and will remain in Fault Mode until the dryer is addressed.

NOTE: If a model error occurs, the microprocessor will always default to the “gas” type for safety reasons. Also, the dryer is stopped and forced into a restart condition to reevaluate ALL expected responses.

65

Page 66 Page 68
Image 67
Page 66 Page 68
Contents DMC Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Free Mode Coin ModeHOT Keys Scrolling Rate Pause ModeRPM Wrinkle Guard Accessing Coin VaultClearing Fault Records and Credit Clearing CREDIT/CLEARING CycleA.F.E. System D. Operating Messages Select Temp to Start Messages Common to Coin and Free ModesClose Lint Access Select Temp Scale Select Buzzer ModeSelect DRY Mode Select LanguageReady Prompt Select Rotation Sensor ModeEnter Lint Cleaning Frequency 0 to 10 Hours Pause Time 0 to 3 MinutesThermistor Temp SET Point 100 to 400F Coin ModeFree Mode Axial Thermistor InputCool Time 0 to 9 Minutes Currency SymbolTime for TOP OFF 1 to 99 Minutes Enter High DRY Temp 100 to 190FAccumulative Time Select Vending ModeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Enter LEFT/RIGHT Coin Denomination 0.05 to Select Vending SafeguardNo Faults FaultsIntroduction to Programming Programming InstructionsProgram Location Summary MED Programming FlowchartsFlowchart Table of Contents READY, Insert Program ModeControl Settings Select Language English Spanish Temp Scale Selecting Display LanguageSelect Language Select Temp Scale Select Buzzer Mode Control SettingsSelecting Temp Scale Count Selecting Buzzer ModeControl Settings Select Language Buzzer Mode OFFSelect DRY Mode Control Settings Select Language Beep Count 1 to 9 BeepsSelecting Beep Count Minutes Selecting DRY ModeFree DRY Mode Select Pause Time 0 toSelect Language Pause Time 0 to Minutes Select Ready Prompt Selecting Pause TimeReady Selecting Ready PromptMachine Rotation Machine Settings Select Model Type GAS Single MotorSelecting Model Type Electric Single MotorSetting Rotation Sensor Machine Setting Lint Cleaning FrequencySettings Axial Lint Cleaning Frequency 0 to HoursAxial Thermistor Input Setting Axial Thermistor InputOFF Temp SetpointThermistor Temp Setting Thermistor Temp SET PointHI KEY- Setting Time for Amount to Start Time for TOP HI KEY- Setting Time for TOP OFFTime for TOP OFF To 99 Minutes Cool Time 0 to Minutes HI KEY- Setting DRY Temp 100 to 190 FPL #03 HI KEY Settings Time for Amount to Start 1 to MinutesPL#04 MED KEY Settings HI KEY- Setting Cool Time 0 to 9 MinutesTime for Amount to Start 1 to Minutes MED KEY- Setting Time for Amount to StartPL #01 Control Settings PL #04 MED KEY SettingsMED KEY- Setting Time for TOP OFF Cool Time 0 to Minutes MED KEY- Setting DRY Temp 100 to 190 FPL #05 LO KEY Settings MED KEY- Setting Cool Time 0 to 9 MinutesLO KEY- Setting Time for Amount to Start Time for TOP OFF To 99 Minutes LO KEY- Setting Time for TOP OFFLO KEY- Setting DRY Temp 100 to 190 F PL #06 Vending Parameters LO KEY- Setting Cool Time 0 to 9 MinutesVending Mode Selecting Currency SymbolSelecting Vending Mode Selecting Vending Safeguard Control Settings PL #06 Vending Setting Left Coin DenominationAmount to Start 0.05 to Setting Right Coin DenominationAmount for Setting Amount to StartTOP OFF 0.05 to PL#07 Fault Recording Setting Amount for TOP OFF 0.05 toAmount for TOP OFF Upper Dryer Faults Accessing Upper Dryer Fault RecordsPL #01 Control Settings PL #07 Fault RecordingPL #01 Control Settings PL #07 Fault Recording Accessing Lower Dryer Fault RecordsLower Dryer Faults Flowchart for Clearing Credit YES Accessing and Clearing Coin Vault TotalLO KEY Settings Factory DefaultsHI KEY Settings MED KEY SettingsControl Settings Language READY-INSERT Amount to Start Fault RecordingUSD Error Messages Diagnostic L.C.D. Fault MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions Drive Green L.E.D FAN Green L.E.D FSS Green L.E.D INPUT/OUTPUT I/O Board L.E.D. IndicatorsLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08
Top Page Image Contents