American Dryer Corp None user manual Accumulative Coin

Page 22

ACCUMULATIVE COIN

In Accumulative Coin Mode, additional time can only be achieved when the AMOUNT FOR TOP OFF (PL #06) has been inserted.

If a coin is inserted into the dryer, which is less than the AMOUNT FOR TOP OFF the Phase 7 dual microprocessor controller (DMC) computer will prompt the user to add more credit for more time with the following message “ADD XX FOR ADDITIONAL TIME”. The Phase 7 DMC (computer) will scroll this message for 30-seconds and then will return to the normal drying cycle information. The credit that was just inserted will be kept in escrow until more credit is inserted to meet the AMOUNT FOR TOP OFF, or the cycle finishes. In the event that the cycle finishes, any credit that was left in escrow will now be applied to the next cycle. Below are examples of different scenarios in Accumulative Coin Mode.

Single Coin Acceptor

Example No. 1: If the dryer is equipped with a 25¢ coin acceptor and the AMOUNT TO START (PL #06) is 50¢, AMOUNT FOR TOP OFF (PL #06) is 50¢, the HI key TIME FOR AMOUNT TO START (PL #03) is 24 minutes, and the HI key TIME FOR TOP OFF (PL #03) is 12 minutes. The initial first two (2) coins will yield 24 minutes and each additional two (2) coins entered into the dryer will yield 12 minutes; no time will be vended if only one (1) coin is inserted.

Settings: PL #06 (LEFT COIN DENOMINATION)

25

PL #03 (TIME FOR AMOUNT TO START)

24

PL #03 (TIME FOR TOP OFF)

12

PL #06 (AMOUNT TO START)

50

PL #06 (AMOUNT FOR TOP OFF)

50

Formula: (AMOUNT TO START [PL #06]) = Vended Time is TIME FOR AMOUNT TO START (PL #03) 50¢ = 24 minutes

(AMOUNT FOR TOP OFF [PL #06]) = Vended Time is TIME FOR TOP OFF (PL #03)

50¢ = 12 minutes

Example No. 2: If the dryer is equipped with a 25¢ coin acceptor and the AMOUNT TO START (PL #06) is 50¢, AMOUNT FOR TOP OFF (PL #06) is 25¢, the MED key TIME FOR AMOUNT TO START (PL #04) is 24 minutes, and the MED key TIME FOR TOP OFF is 12 minutes. The initial first two (2) coins will yield 24 minutes and each additional coin entered into the dryer will yield 12 minutes.

After the AMOUNT TO START (PL #06) has been met, each additional coin entered into the dryer will yield 12 minutes.

Settings: PL #06 (LEFT COIN DENOMINATION)

25

PL #04 (TIME FOR AMOUNT TO START)

24

PL #04 (TIME FOR TOP OFF)

12

PL #06 (AMOUNT TO START)

50

PL #06 (AMOUNT FOR TOP OFF)

25

Formula: (AMOUNT TO START [PL #06]) = Vended Time is TIME FOR AMOUNT TO START (PL #04) 50¢ = 24 minutes

(AMOUNT FOR TOP OFF [PL #06]) = Vended Time is TIME FOR TOP OFF (PL #04)

25¢ = 12 minutes

20

Page 21 Page 23
Image 22
Page 21 Page 23
Contents DMC Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Coin Mode Free ModeHOT Keys Scrolling Rate Pause ModeRPM Clearing CREDIT/CLEARING Cycle Accessing Coin VaultClearing Fault Records and Credit Wrinkle GuardA.F.E. System D. Operating Messages Messages Common to Coin and Free Modes Select Temp to StartClose Lint Access Select Language Select Buzzer ModeSelect DRY Mode Select Temp ScalePause Time 0 to 3 Minutes Select Rotation Sensor ModeEnter Lint Cleaning Frequency 0 to 10 Hours Ready PromptAxial Thermistor Input Coin ModeFree Mode Thermistor Temp SET Point 100 to 400FEnter High DRY Temp 100 to 190F Currency SymbolTime for TOP OFF 1 to 99 Minutes Cool Time 0 to 9 MinutesSelect Vending Mode Accumulative TimeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Faults Select Vending SafeguardNo Faults Enter LEFT/RIGHT Coin Denomination 0.05 toProgramming Instructions Introduction to ProgrammingProgram Location Summary Programming Flowcharts MEDFlowchart Table of Contents Selecting Display Language Program ModeControl Settings Select Language English Spanish Temp Scale READY, InsertSelect Language Select Temp Scale Select Buzzer Mode Control SettingsSelecting Temp Scale OFF Selecting Buzzer ModeControl Settings Select Language Buzzer Mode CountSelect DRY Mode Control Settings Select Language Beep Count 1 to 9 BeepsSelecting Beep Count Select Pause Time 0 to Selecting DRY ModeFree DRY Mode MinutesSelecting Pause Time Select Language Pause Time 0 to Minutes Select Ready PromptReady Selecting Ready PromptMachine Electric Single Motor Machine Settings Select Model Type GAS Single MotorSelecting Model Type RotationSetting Rotation Sensor Lint Cleaning Frequency 0 to Hours Setting Lint Cleaning FrequencySettings Axial MachineTemp Setpoint Setting Axial Thermistor InputOFF Axial Thermistor InputSetting Thermistor Temp SET Point Thermistor TempHI KEY- Setting Time for Amount to Start Time for TOP HI KEY- Setting Time for TOP OFFTime for TOP OFF To 99 Minutes Time for Amount to Start 1 to Minutes HI KEY- Setting DRY Temp 100 to 190 FPL #03 HI KEY Settings Cool Time 0 to MinutesHI KEY- Setting Cool Time 0 to 9 Minutes PL#04 MED KEY SettingsPL #04 MED KEY Settings MED KEY- Setting Time for Amount to StartPL #01 Control Settings Time for Amount to Start 1 to MinutesMED KEY- Setting Time for TOP OFF MED KEY- Setting DRY Temp 100 to 190 F Cool Time 0 to MinutesMED KEY- Setting Cool Time 0 to 9 Minutes PL #05 LO KEY SettingsLO KEY- Setting Time for Amount to Start LO KEY- Setting Time for TOP OFF Time for TOP OFF To 99 MinutesLO KEY- Setting DRY Temp 100 to 190 F LO KEY- Setting Cool Time 0 to 9 Minutes PL #06 Vending ParametersSelecting Currency Symbol Vending ModeSelecting Vending Mode Selecting Vending Safeguard Setting Left Coin Denomination Control Settings PL #06 VendingSetting Right Coin Denomination Amount to Start 0.05 toAmount for Setting Amount to StartTOP OFF 0.05 to PL#07 Fault Recording Setting Amount for TOP OFF 0.05 toAmount for TOP OFF PL #07 Fault Recording Accessing Upper Dryer Fault RecordsPL #01 Control Settings Upper Dryer FaultsPL #01 Control Settings PL #07 Fault Recording Accessing Lower Dryer Fault RecordsLower Dryer Faults Flowchart for Clearing Credit Accessing and Clearing Coin Vault Total YESMED KEY Settings Factory DefaultsHI KEY Settings LO KEY SettingsControl Settings Language READY-INSERT Amount to Start Fault RecordingUSD Error Messages Diagnostic L.C.D. Fault MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions INPUT/OUTPUT I/O Board L.E.D. Indicators Drive Green L.E.D FAN Green L.E.D FSS Green L.E.DLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08
Top Page Image Contents