American Dryer Corp None Time for TOP OFF 1 to 99 Minutes, Enter High DRY Temp 100 to 190F

Page 19

TIME FOR TOP OFF 1 TO 99 MINUTES

This location determines the time that is vended once the AMOUNT FOR TOP OFF is met. This is programmable from 1 minute to 99 minutes, in 1 minute increments. Each temperature setting has its own TIME FOR TOP OFF so that each temperature setting can charge at a different rate.

TIME FOR TOP OFF is only used when the Phase 7 dual microprocessor controller (DMC) computer is set in Accumulative Coin Mode. When a cycle is started, the Phase 7 DMC (computer) uses TIME FOR AMOUNT TO START 1 TO 99 MINUTES to determine the initial amount of time vended for a temperature key. Once a cycle is started, the Phase 7 DMC (computer) will then reference this TIME FOR TOP OFF for any additional time needed, before any additional time is vended the user will first need to meet the AMOUNT FOR TOP OFF. When a cycle is restarted from Pause Mode, the Phase 7 DMC (computer) will calculate how much time is left in the cycle for the new temperature selected. These calculations are based on a combination of the TIME FOR AMOUNT TO START and TIME FOR TOP OFF for the new temperature key selected and the amount of credit that was available at the time the Phase 7 DMC (computer) was placed into Pause Mode. In Accumulative Coin Mode, the AMOUNT TO START and AMOUNT FOR TOP OFF can differ, so the rate charged for TIME FOR AMOUNT TO START and TIME FOR TOP OFF can be different. The Phase 7 DMC (computer) accounts for the different rates by tracking how much credit is available from AMOUNT TO START and the credit that is available from TIME FOR TOP OFF. Using these ratios of credit and time, the Phase 7 DMC (computer) will determine how much time is left in the cycle for the new temperature key selected.

ENTER HIGH DRY TEMP 100 TO 190°F

Each temperature cycle “HIGH,” “MED,” and “LO” can be programmed to a dry temperature ranging from 100°F to 190°F (38°C to 87°C) in Radial Mode or 100°F to 150°F (38°C to 66°C) in Axial Mode.

COOL TIME 0 TO 9 MINUTES

Cool down time ranges from 0 to 9 minutes. The cool down time occurs at the end of a dry cycle. If your cool down time is set to 4 minutes, the last 4 minutes of the dry cycle will be in Cool Down Mode.

PL #06 – VENDING PARAMETERS

CURRENCY SYMBOL

The Phase 7 DMC (computer) can be programmed to display ALL currency in one (1) of the following currency symbols, a token mode, none, and no symbol or decimal point.

USD / UK Pound / EURO / Yen / Token / None / No Symbol or Decimal

NOTE: When the Phase 7 DMC (computer) is set to TOKEN ALL of the coin related menu items will change from currency to whole numbers. The LEFT and RIGHT COIN VALUES will change to a default of one (1) token. The AMOUNT TO START and AMOUNT FOR TOP OFF will also default to one (1). If the currency symbol is changed back to a currency symbol these menu items will change back to factory defaults. The default setting are LEFT COIN DENOMINATION – 0.25, RIGHT COIN DENOMINATION – 0.10, AMOUNT TO START – 0.25, and AMOUNT FOR TOP OFF – 0.25.

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents DMC Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceTable of Contents Section Phase 7 Dual Microprocessor Controller DMC Computer Section Features Keyboard Touch Pad Symbols = PAUSE/CLEAR key Free Mode Coin ModeHOT Keys Scrolling Rate Pause ModeRPM Wrinkle Guard Accessing Coin VaultClearing Fault Records and Credit Clearing CREDIT/CLEARING CycleA.F.E. System D. Operating Messages Select Temp to Start Messages Common to Coin and Free ModesClose Lint Access Select Temp Scale Select Buzzer Mode Select DRY Mode Select LanguageReady Prompt Select Rotation Sensor ModeEnter Lint Cleaning Frequency 0 to 10 Hours Pause Time 0 to 3 MinutesThermistor Temp SET Point 100 to 400F Coin ModeFree Mode Axial Thermistor InputCool Time 0 to 9 Minutes Currency SymbolTime for TOP OFF 1 to 99 Minutes Enter High DRY Temp 100 to 190FAccumulative Time Select Vending ModeDual CoinAcceptor Accumulative Coin Dual CoinAcceptor Enter LEFT/RIGHT Coin Denomination 0.05 to Select Vending SafeguardNo Faults FaultsIntroduction to Programming Programming InstructionsProgram Location Summary MED Programming FlowchartsFlowchart Table of Contents READY, Insert Program ModeControl Settings Select Language English Spanish Temp Scale Selecting Display LanguageSelect Language Select Temp Scale Select Buzzer Mode Control SettingsSelecting Temp Scale Count Selecting Buzzer ModeControl Settings Select Language Buzzer Mode OFFSelect DRY Mode Control Settings Select Language Beep Count 1 to 9 BeepsSelecting Beep Count Minutes Selecting DRY ModeFree DRY Mode Select Pause Time 0 toSelect Language Pause Time 0 to Minutes Select Ready Prompt Selecting Pause TimeReady Selecting Ready PromptMachine Rotation Machine Settings Select Model Type GAS Single MotorSelecting Model Type Electric Single MotorSetting Rotation Sensor Machine Setting Lint Cleaning FrequencySettings Axial Lint Cleaning Frequency 0 to HoursAxial Thermistor Input Setting Axial Thermistor InputOFF Temp SetpointThermistor Temp Setting Thermistor Temp SET PointHI KEY- Setting Time for Amount to Start Time for TOP HI KEY- Setting Time for TOP OFFTime for TOP OFF To 99 Minutes Cool Time 0 to Minutes HI KEY- Setting DRY Temp 100 to 190 FPL #03 HI KEY Settings Time for Amount to Start 1 to MinutesPL#04 MED KEY Settings HI KEY- Setting Cool Time 0 to 9 MinutesTime for Amount to Start 1 to Minutes MED KEY- Setting Time for Amount to StartPL #01 Control Settings PL #04 MED KEY SettingsMED KEY- Setting Time for TOP OFF Cool Time 0 to Minutes MED KEY- Setting DRY Temp 100 to 190 FPL #05 LO KEY Settings MED KEY- Setting Cool Time 0 to 9 MinutesLO KEY- Setting Time for Amount to Start Time for TOP OFF To 99 Minutes LO KEY- Setting Time for TOP OFFLO KEY- Setting DRY Temp 100 to 190 F PL #06 Vending Parameters LO KEY- Setting Cool Time 0 to 9 MinutesVending Mode Selecting Currency SymbolSelecting Vending Mode Selecting Vending Safeguard Control Settings PL #06 Vending Setting Left Coin DenominationAmount to Start 0.05 to Setting Right Coin DenominationAmount for Setting Amount to StartTOP OFF 0.05 to PL#07 Fault Recording Setting Amount for TOP OFF 0.05 toAmount for TOP OFF Upper Dryer Faults Accessing Upper Dryer Fault RecordsPL #01 Control Settings PL #07 Fault RecordingPL #01 Control Settings PL #07 Fault Recording Accessing Lower Dryer Fault RecordsLower Dryer Faults Flowchart for Clearing Credit YES Accessing and Clearing Coin Vault TotalLO KEY Settings Factory DefaultsHI KEY Settings MED KEY SettingsControl Settings Language READY-INSERT Amount to Start Fault RecordingUSD Error Messages Diagnostic L.C.D. Fault MessagesStandards Page Page Page A.F.E. System Diagnostic Conditions Drive Green L.E.D FAN Green L.E.D FSS Green L.E.D INPUT/OUTPUT I/O Board L.E.D. IndicatorsLint RED L.E.D Keyboard Touch PAD Layout Page ADC Part No 10/01/08
Top Page Image Contents