Icom EX-2714, MR-1000TTM, MR-1000RTM instruction manual Installing the display unit

Page 29

Installing the display unit

DLocation

Select a place for installation which meets the following important conditions:

qThe display unit should be placed near the wheel in the cabin so that an operator may easily view the radar screen while facing the bow.

wTo minimize interference, KEEP the unit AT LEAST THE COMPASS SAFE DISTANCE stated in the se- rial No. seal on the rear panel away from the com- pass and navigation receiver.

eSelect a position where there is no danger of salt or fresh water spray or immersion.

rSelect a location where it is easy to perform main- tenance or adjustment after installation.

tSelect a location which can support the weight of the display unit.

yDO NOT select areas subject to extreme heat, cold, vibrations or direct sunlight.

SX-2713/2779 Mounting Bracket

INSTALLATION AND CONNECTIONS

9

DMounting

The mounting bracket supplied with the display unit al- lows “dashboard” or “overhead” mounting.

qHold the mounting bracket up to the selected loca- tion and mark pilot holes for the 5 installation holes

using the template.

The template is provide on p.41.

wDrill 5 holes of 3 mm (18 in) in diameter as shown in the diagram. (Fig. 1)

eInstall the bracket using the screws, nuts, bolts or washers, with the supplied accessories. (Fig. 2)

rAdjust the display unit to an adequate view angle. t Install the supplied viewing hood.

Mounting Bracket installation

250(92732)

195(71116)

97.5(32732)

Ø7 (932)

Ø7 (932)4

30 (1316)

60 (238)

100 (31516)

Fig. 1Fig. 2

SX-2713/2779

269 (101932)

MARINE RADAR

POWER

TX

SAVE

MOB

TARGET TRAILS

ZOOM

ALM MODE

OFF CENT

EBL1 EBL2

VRM1 VRM2

PI

BRILL MENU

HL OFF

264 (101332)

258 (10532)

48 (12932)

 

 

16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

16)

 

132 (5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

287 (11

 

16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

132 (5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Viewing hood installation

25

Image 29
Contents MR-1000R EX-2714Radome type unit Qty System cable OPC-1188 15 m Model Name CRT Display Scanner UnitEX-2780Open array type unit Qty SX-2713/277910 inch CRT display unitWord Definition Rine RadarTable of Contents Radiation Hazard Front panel Panel Description@0DISPLAY Brilliance Switch Brill 9EBL1 VRM1 Switch EBL1 VRM10PARALLEL Index Line Function PI 2HEADING Line OFF Function HL OFFScreen @9MODE Indicator$3HEADING Indicator #9CURSOR Indicator$8OWN Ship Vector Indicator 6TIME Indicator %7TIME IndicatorMenu ATA Automatic Tracking Aid Turning power ON/OFF Checking the installationChecklist Basic OperationBasic operation OFF Center function Rain functionSEA function Stretch function IR functionZoom function Zoom function expands the target to two times normal sizeTrails function Power save functionShip speed indication Bearing settingPosition indication Waypoint indicationUsing the variable range marker Using the fixed ringsDistance and Direction Measurements Distance measurementBearing and Distance measurement Using the EBL and VRMDistance and Direction Measurements Push EBL1 VRM1/ to clear EBL1 and VRM1Measuring the distance and direction between 2 targets Advanced measurementsPush EBL2 VRM2/ to display the EBL2 and VRM2 Push Ù Ú Ω ≈ to move the cursor on the other targetAlarm zone setting Alarm FunctionZone alarm setting Setting and using the alarm functionATA Automatic Tracking Aid ATA menu settingATA Automatic Tracking Aid ATA operationPlotting marks Course and speed vector ATA PlotsIndirect echoes Basic Radar TheorySide-lobe echoes Basic Radar Theory Multiple echoesMinimum range Distance resolution Target resolutionDirection resolution Blind and Shadow sectorsConnecting the units Installation and ConnectionsPower source requirement Ground connectionInstalling the display unit Ship’s bow direction Mounting the EX-2714 scanner unitConnect the system cable Wiring the EX-2714 system cableScanner unit disassembly Mounting the EX-2780 scanner unit Wiring the EX-2780 system cable Beacon Fixing the EX-2780 scanner unitOther Functions All resetAntenna rotation speed Test pattern indicationSelect the language Service MAN MenuService man menu Service MAN Menu Timing adjustmentHDG adjustment Range selection SPD adjustmentMessage Condition Error MessageError message list Periodic maintenance MaintenanceScanner unit maintenance Display unit maintenanceEX-2780 Open array SpecificationsEX-2714 Radome Display unit SpecificationsBearing Speed Position External Data ListSX-2713/2779 Display mounting bracket template EX-2714 Radome template EX-2780 Open array type template