Icom MR-1000TTM, MR-1000RTM, EX-2714 Error Message, Error message list, Message Condition

Page 39

ERROR MESSAGE 12

■Error message list

Message

Condition

 

 

BRG INPUT FAIL*1

• The Azimuth signal is interrupted. An alarm tone is emitted within

 

5 sec. and the display reverts to H UP mode in approx. 1 min.

 

 

TRIG SIGNAL FAIL*1

• If the TRIGGER signal is interrupted for more than 15 sec., an alarm

 

tone is emitted.

 

 

SHM SIGNAL FAIL*2

• If the SHM signal is interrupted for more than 15 sec., an alarm tone is

 

emitted.

 

 

POSN INPUT FAIL*1

• If the position signal is interrupted for more than 15 sec., an alarm tone

 

is emitted.

 

 

CHECK SCANNER CONNECTION*4

• The system cable may not be connected properly.

 

 

*1 Push any key to cancel the error message and beep tone. Turn the power OFF, then check the external data cable connection.

*2 An electricity failure may occur, turn the power OFF, then consult your dealer or service man. *3 Push any key to cancel the error message and beep tone.

*4 Turn the power OFF, then check the system cable connections.

35

Page 38 Page 40
Image 39
Page 38 Page 40
Contents
MR-1000R SX-2713/277910 inch CRT display unit Model Name CRT Display Scanner UnitEX-2714Radome type unit Qty System cable OPC-1188 15 m EX-2780Open array type unit QtyWord Definition Rine RadarTable of Contents Radiation Hazard Front panel Panel Description2HEADING Line OFF Function HL OFF 9EBL1 VRM1 Switch EBL1 VRM1@0DISPLAY Brilliance Switch Brill 0PARALLEL Index Line Function PIScreen @9MODE Indicator6TIME Indicator %7TIME Indicator #9CURSOR Indicator$3HEADING Indicator $8OWN Ship Vector IndicatorMenu ATA Automatic Tracking Aid Basic Operation Checking the installationTurning power ON/OFF ChecklistBasic operation Rain function SEA functionOFF Center function Zoom function expands the target to two times normal size IR functionStretch function Zoom functionTrails function Power save functionWaypoint indication Bearing settingShip speed indication Position indicationDistance measurement Using the fixed ringsUsing the variable range marker Distance and Direction MeasurementsPush EBL1 VRM1/ to clear EBL1 and VRM1 Using the EBL and VRMBearing and Distance measurement Distance and Direction MeasurementsPush Ù Ú Ω ≈ to move the cursor on the other target Advanced measurementsMeasuring the distance and direction between 2 targets Push EBL2 VRM2/ to display the EBL2 and VRM2Setting and using the alarm function Alarm FunctionAlarm zone setting Zone alarm settingATA Automatic Tracking Aid ATA menu settingATA operation Plotting marks Course and speed vectorATA Automatic Tracking Aid ATA PlotsBasic Radar Theory Side-lobe echoesIndirect echoes Multiple echoes Minimum rangeBasic Radar Theory Blind and Shadow sectors Target resolutionDistance resolution Direction resolutionGround connection Installation and ConnectionsConnecting the units Power source requirementInstalling the display unit Ship’s bow direction Mounting the EX-2714 scanner unitWiring the EX-2714 system cable Scanner unit disassemblyConnect the system cable Mounting the EX-2780 scanner unit Wiring the EX-2780 system cable Beacon Fixing the EX-2780 scanner unit Test pattern indication All reset Other Functions Antenna rotation speedService MAN Menu Service man menuSelect the language Timing adjustment HDG adjustmentService MAN Menu Range selection SPD adjustmentError Message Error message listMessage Condition Display unit maintenance MaintenancePeriodic maintenance Scanner unit maintenanceSpecifications EX-2714 RadomeEX-2780 Open array Display unit SpecificationsBearing Speed Position External Data ListSX-2713/2779 Display mounting bracket template EX-2714 Radome template EX-2780 Open array type template
Top Page Image Contents