■ATA (Automatic Tracking Aid)
MENU 3
■INT. SETTING
| A T A MENU | ||
|
|
|
|
A T A |
|
| OFF |
No.DISP |
|
| OFF |
VECT |
|
| TRUE |
OWN VECT |
|
|
|
|
| OFF | |
ALARM |
|
|
|
|
| OFF | |
CPA LIMIT |
|
| 1.0NM |
TCPA LIMIT |
|
| 1 MIN |
ON
SEL
REL
ON ON
ALL
MAG VAR
BRG INPUT SPD INPUT TX INH START TX INH ANGLE SAVE TIME SYMBOL
CHARACTER KEY ILLUM
INT. SETTING
| AUTO | MANUAL |
| |||||||
|
|
|
|
|
|
| 7.2˚ W |
| ||
NMEA |
| N+1 | AUX | GPS | ||||||
|
|
|
|
|
|
| LOG |
| ||
| GPS |
|
|
|
| |||||
|
|
| 0˚ |
|
|
|
|
|
| |
| 1M | 0˚ |
|
| 15M | 30M | ||||
|
|
| 6M |
| ||||||
|
| 2 | 3 |
|
|
|
| |||
1 |
|
|
|
|
| |||||
1 |
|
|
| 3 |
|
|
| BRILL | ||
2 |
|
|
| |||||||
1 |
| 2 | 3 |
| 4 |
|
| |||
DATA
• OFF | : Turn the ATA function OFF. |
• ON | : Turn the ATA function ON. |
DNo.DISP
• OFF | : Non display any mark number. |
• Sel | : Display the selected mark number |
| only. |
• ALL | : Display all mark numbers. |
DVECT
• TRUE | : Select the true vector mode. |
• REL | : Select the relative vector mode. |
DOWN VECT
• OFF | : Non display the own ship vector. |
• ON | : Display your own ship’s vector. |
DALARM (CPA/TCPA)
• OFF | : Turn the alarm function OFF. |
• ON | : Turn the alarm function ON. |
DCPA* LIMIT
•0.1 to 10.0NM : Set the CPA (Closest Point of Ap- proach) limit with [Ω ≈].
DTCPA* LIMIT
• 1 to 60MIN : Set the TCPA (Time to CPA) limit time with [Ω ≈].
*CPA/TCPA: Closest Point of Approach and Time to Clos- est Point of Approach limit is defined by the observer to given warning when a target or targets are close to within those limits from your own ship.
DMAG VAR
• AUTO | : Revise magnetic variation automatically. |
| NOTE: NMEA data is required. NEVER select |
| “AUTO” without NMEA data, incorrect varia- |
| tion data may entered. (p. 39) |
•MANUAL : Revise magnetic variation manually.
•Push [≈] to select [MANUAL], then push [Ú]. Set the revise value with [Ω ≈]. Push [Ú] or [MENU] to abort the menu.
DBRG INPUT
• NMEA : NMEA0183 bearing data format.
•N+1 : N+1 data format.
• AUX | : Other format. |
• GPS | : Reads NMEA0183 COG format data as |
| HDG format. |
DSPD INPUT
• GPS | : Use the GPS NMEA speed data. |
• LOG | : Use the speed sensor data. |
DTX INH START
•0 to 359° : Push [Ω ≈] to enter the start point of the TX inhibit area.
DTX INH ANGLE
•0 to 90° : Push [Ω ≈] to enter the TX inhibit area.
DSAVE TIME
•1M, 6M, 15M or 30M
:Select the stand by time during save mode.
* The radar for TX interval scan is fixed at 10 revolutions.
DSYMBOL
•1/2/3 : Select the symbol brightness.
DCHARACTER
•1/2/3 : Select the character brightness.
DKEY ILLUM
•1/2/3/4 : Select the key illumination brightness.
7