Furuno GP32 Programming Dgps user channels stations, Editing Dgps user channels, Station Nearest

Page 46

7.OTHER FUNCTIONS

d)Use the cursor pad to enter the transmission frequency of the DGPS beacon station to be used and then press the [ENT] key.

LIST

a)The following display appears after pressing the [ENT] key at step 6.

STATION (NEAREST)

	[EXIT]		[USER]			92°
	310.0			29.1 nm		92°
287.0				56.7 nm		134°
292.0				160 nm		320°
321.0				234 nm		134°
302.0				426 nm		121° *




Tx frequency of						"*" denotes
beacon station						user channel.

Range (ref. only) and bearing from ship to beacon station

DGPS beacon station list

b)Use the cursor pad to choose station desired.

c)Press the [ENT] key.

8.Press the [MENU] key twice to finish.

Programming DGPS user channels (stations)

The user may program 20 DGPS beacon stations from which to use in DGPS beacon station selection. Whenever a new station is constructed you can add it to the list.

1.Press the [MENU] key twice to open the menu.

2.Choose DGPS/WAAS and then press the [ENT] key.

3.Choose DGPS STATION and then press the [ENT] key.

4.Choose LIST and then press the [ENT] key.

5.Choose USER and then press the [ENT] key.

STATION (USER)

[EXIT] [NEW?] [CLR?]

01 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

02 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

03 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

04 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

05 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

06 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

DGPS STATION (USER) list

6.Choose “NEW?” and then press the [ENT] key.

NEW USER CHANNEL

STATION (USER)

FREQ	:		310.0kHz
RATE	:		200BPS
LAT	:		37° 59'N
LON	:		123° 00'W
EXIT?	SAVE?

NEW USER CHANNEL (DGPS) set up menu

7.Press the [ENT] key, enter frequency of the station, and then press the [ENT] key.

8.Press the [ENT] key, enter baud rate of the station, and then press the [ENT] key.

9.Press the [ENT] key, enter latitude of the

station, and then press the [ENT] key.

10 Press the [ENT] key, enter longitude of the station, and then press the [ENT] key.

11.Choose “SAVE?” and then press the [ENT] key.

12.Press the [MENU] key twice to finish.

Editing DGPS user channels

1.Press the [MENU] key twice to open the menu.

2.Choose WAAS/DGPS and then press the [ENT] key.

3.Choose DGPS STATION and then press the [ENT] key.

4.Choose LIST and then press the [ENT] key.

5.Choose USER and then press the [ENT] key.

36

Image 46

Contents Page 00080928811 Safety Instructions Safety Instructions for the Installer Table of Contents Outline Drawings Foreword FeaturesWord to the Owner of the GP-37, GP-32 GP-37 system configuration System ConfigurationGP-32 system configuration What is WAAS? Msas Egnos WaasOptional equipment Equipment ListsStandard supply Name Type Code No Qty RemarksControls How to attach and remove the hard coverOperational Overview Control panelTurning on the power Turning On and Off PowerAdjusting Brilliance and Contrast Turning off the powerDisplay modes default user displays Display ModesPlotter display Plotter displayHighway display Highway displaySteering display Steering displayNav data display Nav data displayDigital display Digital display default displayUser displays Speedometer displayOFF How to enter alphanumeric dataMenu Overview AutoSimulator menu Simulation DisplaySimulator display, auto course selected Shifting the Cursor Plotter Display OverviewChoosing the Display Range Cursor state and dataChanging Track Plotting Interval, Stopping Plotting Shifting the DisplayCentering Own Ship’s Position OFFErase Track Erasing TrackErase menu YESPlotter Display Overview This page intentionally left blank Entering Waypoints Waypoints MarksEntering a waypoint with the cursor WPTS/MARKS List Entering a waypoint at own ship positionEntering a waypoint from the waypoint list GPS POS. → MarkMark Entering the MOB MarkEnter a NEW WPT Name Saved to MOB GO to MOB ?DSP RTE DSP ALL Displaying Waypoint NameOperations on the Waypoint List Editing waypointsWPTS/MARKS Nearest Erasing WaypointsShowing nearest waypoints by distance, TTG and ETA Name KobeSpeed for Calculating Time-to-Go, Estimated Time of Arrival Creating a route with the cursor RoutesCreating Routes Sample routeRoutes Creating a route from the route menuRoutes Creating a route from the waypoint listWPTS/MARKS List Creating a track-based route automatically Creating a track-based routeCreating a track-based route manually DistanceREMOVE? INSERT? SKIP? Editing RoutesReplacing waypoints in a route NameInserting a waypoint in a route Route contents Route-01Permanently deleting a waypoint from a route Temporarily deselecting a waypoint in a routeErase Route 01 ? Erasing RoutesChanging route comment name YESThis page intentionally left blank WPT-NEAR? OFF?? ROUTE? CURSOR? SETUP? Setting Destination by CursorSetting Destination by Waypoint DestinationCanceling Destination Setting Route as DestinationSetting User Waypoint as Destination REVERSE?Arrival alarm AlarmsArrival Alarm, Anchor Watch Alarm AlarmsAnchor watch alarm XTE Cross Track Error AlarmARV ANC Time Alarm Speed AlarmWAAS/DGPS Alarm WAAS/DGPS mode and alarm messageBuzzer Type Selection Trip AlarmOdometer Alarm Long ConstantRange and bearing between two waypoints Other FunctionsCalculating Range, Bearing, TTG and ETA RouteWaas INT Beacon Waas SetupGPS EXT BeaconDgps setup GPSStation Nearest Programming Dgps user channels stationsEditing Dgps user channels Station UserTrue Bearing ReferenceErasing all user channels Erasing individual user channelsMagnetic Variation Geodetic Chart SystemUnits of Measurement For Loran C TD Time Difference using local time, Time FormatPosition Display Format For Decca TDGPS Setup GPS Setup menu descriptionDigital data User Display SetupSpeedometer Reset trip meter, odometer options Resetting Trip and Odometer DistancesReset Trip METER? Are YOU SURE? YES no ODOMETER? Speedometer displayUploading, Downloading Waypoint, Route Data WiringSetting for communication software on Downloading/Uploading between PC and GP-37/GP-32Uploading data from a PC Loading data from a YeomanWaypoint data format Route data formatEnd of sentence LanguageRoute comment data format EspanolDisplaying the Message Board Maintenance & TroubleshootingMaintenance MessagesReady for Battery Change Press ANY KEY To Shut Down Replacing the BatteryExchange BATTERY? Replacing the FuseSatellite monitor display DiagnosticsSatellite Monitor Display Test START? promptClearing Data Language and default position, unit and time difference Language Default Position Unit Time DifferenceThis page intentionally left blank Mounting considerations InstallationInstallation of Display Unit Desktop and overhead mountingFlush mount S kit Installation of Antenna UnitHow to assemble the connector Flush mount S kit Type OP20-17 Code NoHow to fix spring in fuse holder WiringWiring GroundingDATA1 Current loop data Initial SettingsOutput data format, data sentences DATA2 RS-232C levelSetup menu Output settingDATA1, Data 2 and Nmea version options This page intentionally left blank Appendix Menu TreeStart from -99 to +99 Digital Display divisionAvailable data Odometer, trip , time Interval 01 to 99Geodetic Chart List North AmericanLoran C Chains GRIDecca Chains Chain Location CodeAP-6 Specifications GPS Navigator GP-32 Dgps Navigator GP-37 Power Supply CT4UWOK Feb Hatai Page Page Page GPS Navigator Dgps Navigator Index WAAS/DGPS XTEIndex-2