Furuno GP32 manual Resetting Trip and Odometer Distances, Speedometer display, Speedometer menu

Page 52

7.OTHER FUNCTIONS

8.Use the cursor pad to choose data desired and then press the [ENT] key. NONE: No display

ODO:	Odometer distance
TRIP:	Trip distance
TIME:	Time and date
POSN:	Position
POWER:	Power source voltage
SOG:	Speed over ground
COG:	Course over ground
WPT:	Rng and brg to waypoint
XTE:	Cross-track error
TTG:	Time to go (to destination)
ETA:	Estimated time of arrival
	(at destination)

9.Control returns to the User display setup, with “B” selected. Depending on the selection made at step 5, set other indications similar to how you did with “A”.

10.Press the [MENU] key twice to finish.

Speedometer display

1.Press the [MENU] key once or twice to open the menu.

2.Choose USER DISP and then press the [ENT] key.

3.Choose 1 or 2 and then press the [ENT] key.

4.Choose SPEEDOMETER and then press the [ENT] key.

SPEEDOMETER

START FROM: + 0

INTERVAL : 10

0 10 20 30 40

Start point	Interval

Speedometer menu

5.The cursor is selecting START FROM. Press the [ENT] key.

6.Enter starting speed: Use ◄ or ► to select location and ▲ or ▼ to enter value and switch from plus to minus and vice versa. The setting range is -99 to +99.

7.Press the [ENT] key, and the cursor shifts to INTERVAL.

8.Press the [ENT] key.

9.Enter scale interval: Use ◄ or ► to choose location and ▲ or ▼ to enter value. The setting range is 1 to 99.

10.Press the [ENT] key.

11.Press the [MENU] key twice to close the menu.

7.12Resetting Trip and Odometer Distances

1.Press the [MENU] key once or twice to open the menu.

2.Choose ERASE and then press the [ENT] key.

3.Choose “RESET TRIP?” (or “RESET ODO?”) and then press the [ENT] key. One of following displays appears.

RESET

TRIP METER?

ARE YOU SURE?

YES NO

RESET

ODOMETER?

ARE YOU SURE?

YES NO

Reset trip meter, odometer options

4.Press ◄ to choose YES and then press the [ENT] key to reset distance to zero.

5.Press the [MENU] key twice to finish.

42

Image 52

Contents Page 00080928811 Safety Instructions Safety Instructions for the Installer Table of Contents Outline Drawings Foreword FeaturesWord to the Owner of the GP-37, GP-32 GP-37 system configuration System ConfigurationGP-32 system configuration What is WAAS? Msas Egnos WaasEquipment Lists Standard supplyOptional equipment Name Type Code No Qty RemarksHow to attach and remove the hard cover Operational OverviewControls Control panelTurning On and Off Power Adjusting Brilliance and ContrastTurning on the power Turning off the powerDisplay modes default user displays Display ModesPlotter display Highway displayPlotter display Highway displaySteering display Nav data displaySteering display Nav data displayDigital display default display User displaysDigital display Speedometer displayHow to enter alphanumeric data Menu OverviewOFF AutoSimulator menu Simulation DisplaySimulator display, auto course selected Plotter Display Overview Choosing the Display RangeShifting the Cursor Cursor state and dataShifting the Display Centering Own Ship’s PositionChanging Track Plotting Interval, Stopping Plotting OFFErasing Track Erase menuErase Track YESPlotter Display Overview This page intentionally left blank Entering Waypoints Waypoints MarksEntering a waypoint with the cursor Entering a waypoint at own ship position Entering a waypoint from the waypoint listWPTS/MARKS List GPS POS. → MarkEntering the MOB Mark Enter a NEW WPT NameMark Saved to MOB GO to MOB ?Displaying Waypoint Name Operations on the Waypoint ListDSP RTE DSP ALL Editing waypointsErasing Waypoints Showing nearest waypoints by distance, TTG and ETAWPTS/MARKS Nearest Name KobeSpeed for Calculating Time-to-Go, Estimated Time of Arrival Routes Creating RoutesCreating a route with the cursor Sample routeRoutes Creating a route from the route menuRoutes Creating a route from the waypoint listWPTS/MARKS List Creating a track-based route Creating a track-based route manuallyCreating a track-based route automatically DistanceEditing Routes Replacing waypoints in a routeREMOVE? INSERT? SKIP? NameRoute contents Route-01 Permanently deleting a waypoint from a routeInserting a waypoint in a route Temporarily deselecting a waypoint in a routeErasing Routes Changing route comment nameErase Route 01 ? YESThis page intentionally left blank Setting Destination by Cursor Setting Destination by WaypointWPT-NEAR? OFF?? ROUTE? CURSOR? SETUP? DestinationSetting Route as Destination Setting User Waypoint as DestinationCanceling Destination REVERSE?Alarms Arrival Alarm, Anchor Watch AlarmArrival alarm AlarmsAnchor watch alarm XTE Cross Track Error AlarmARV ANC Speed Alarm WAAS/DGPS AlarmTime Alarm WAAS/DGPS mode and alarm messageTrip Alarm Odometer AlarmBuzzer Type Selection Long ConstantOther Functions Calculating Range, Bearing, TTG and ETARange and bearing between two waypoints RouteWaas Setup GPSWaas INT Beacon EXT BeaconDgps setup GPSProgramming Dgps user channels stations Editing Dgps user channelsStation Nearest Station UserBearing Reference Erasing all user channelsTrue Erasing individual user channelsMagnetic Variation Geodetic Chart SystemUnits of Measurement Time Difference using local time, Time Format Position Display Format For Loran C TD For Decca TDGPS Setup GPS Setup menu descriptionDigital data User Display SetupSpeedometer Resetting Trip and Odometer Distances Reset Trip METER? Are YOU SURE? YES no ODOMETER?Reset trip meter, odometer options Speedometer displayWiring Setting for communication software onUploading, Downloading Waypoint, Route Data Downloading/Uploading between PC and GP-37/GP-32Uploading data from a PC Loading data from a YeomanWaypoint data format Route data formatLanguage Route comment data formatEnd of sentence EspanolMaintenance & Troubleshooting MaintenanceDisplaying the Message Board MessagesReplacing the Battery Exchange BATTERY?Ready for Battery Change Press ANY KEY To Shut Down Replacing the FuseDiagnostics Satellite Monitor DisplaySatellite monitor display Test START? promptClearing Data Language and default position, unit and time difference Language Default Position Unit Time DifferenceThis page intentionally left blank Installation Installation of Display UnitMounting considerations Desktop and overhead mountingInstallation of Antenna Unit How to assemble the connectorFlush mount S kit Flush mount S kit Type OP20-17 Code NoWiring WiringHow to fix spring in fuse holder GroundingInitial Settings Output data format, data sentencesDATA1 Current loop data DATA2 RS-232C levelSetup menu Output settingDATA1, Data 2 and Nmea version options This page intentionally left blank Appendix Menu TreeDigital Display division Available data Odometer, trip , timeStart from -99 to +99 Interval 01 to 99Geodetic Chart List North AmericanLoran C Chains GRIDecca Chains Chain Location CodeAP-6 Specifications GPS Navigator GP-32 Dgps Navigator GP-37 Power Supply CT4UWOK Feb Hatai Page Page Page GPS Navigator Dgps Navigator Index WAAS/DGPS XTEIndex-2