Furuno 1833C-BB, GD-1900C-BB Contents of Network setup menu, NavNet equipment default settings

Page 47

Contents of Network setup menu

Item

 

 

Description

 

Default Setting

 

 

 

 

 

 

IP ADDRESS

 

This address is assigned at the factory. Change the

 

 

 

address (last three digits; 001 to 254) when like models

Radar:

 

 

are connected directly or through the hub. Do this

 

 

 

change before connecting the equipment to the other

172.031.003.007

 

 

equipment or hub in order to distinguish equipment. Do

 

 

 

not set the same IP address in the network.

 

 

 

 

 

 

 

 

HOST NAME

 

Set the name for radar or plotter to distinguish it from

MODEL series:

 

 

others in the NavNet system. Confirm that no two

 

 

 

 

RADAR

 

 

equipment have same host names. The host name has

 

 

 

 

 

been preset depending on the series of NavNet. See

 

 

 

GD-1900C-BB:

 

 

the table below. This host name is used for RADAR

 

 

SOURCE and CHART SOURCE.

 

PLOTTER

 

 

 

 

 

 

 

RADAR SOURCE

 

Enter the host name “RADAR (preset)” or the new

 

 

 

 

name set at HOST NAME if the unit has been changed

RADAR

 

 

of the network radar to use for the radar display. Clear

 

 

the RADAR SOURCE name when your equipment is

 

 

 

GD-1900C-BB and no radar is connected.

 

 

 

 

 

 

 

 

CHART SOURCE

 

The driver names of the memory card interface unit are

 

 

 

MCDRIVE-1 (left side) and MCDRIVE-2 (right side).

MCDRIVE

 

 

Additionally, enter a host name (set at HOST NAME) of

 

 

network display unit (max. 3) which can read chart

 

 

 

 

cards.

 

 

 

 

 

 

 

 

 

 

 

SOUNDER SOURCE

 

The host name of the network sounder ETR-6/10N or

 

 

 

ETR-30N is preset (SOUNDER) for use with the video

SOUNDER

 

 

sounder display. Clear the host name when no network

 

 

 

 

 

sounder is connected.

 

 

 

 

 

 

 

 

 

AUX SOURCE

 

For the facsimile receiver FAX-30. Use the default

 

WX FAX

 

 

setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUBNET MASK

 

 

 

 

 

 

255.255.000.000

 

 

Not used. Reserved for future use.

 

 

GATEWAY ADDRESS

 

 

000.000.000.000

 

 

 

 

 

 

 

 

OFFSET PORT NUMBER

 

 

 

 

 

 

10000

 

 

 

 

 

 

 

 

NavNet equipment default settings

 

 

 

 

 

 

 

Model

 

IP ADDRESS

 

 

HOST NAME

 

 

 

 

 

MODEL1823C-BB/1833C-BB/1933C-BB/

 

172.031.003.007

 

RADAR, PLOTTER

1943C-BB/1953C-BB, GD-1900C-BB

 

 

 

 

 

 

 

 

 

 

MODEL1823C/1833C/1933C/

 

172.031.003.003

 

RADAR, PLOTTER

1943C/1953C, GD-1900C

 

 

 

 

 

 

 

 

 

 

 

MODEL1833/1933/1943

 

 

172.031.003.002

 

RADAR

 

 

 

 

 

MODEL1722C/1732C/1742C/1762C/1752C

 

172.031.003.001

 

RADAR

 

 

 

 

 

MODEL1722/1732/1742/1762

 

172.031.003.004

 

RADAR

 

 

 

 

 

 

GD-1700/1700C

 

 

172.031.014.001

 

PLOTTER

 

 

 

 

 

 

CU-200

 

 

172.031.014.100

 

MCDRIVE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3-3

Image 47
Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting of display unit Flush mountingDesktop mounting of display unit Desktop mountingMounting the Processor Unit Processor unit, mounting dimensionsMounting the Antenna Unit of MODEL1823C-BB Typical antenna unit placement on sailboat and powerboatAntenna unit, showing location of mounting hardware How to fasten the mounting base to platformAntenna unit, inside view Snap holder Remove and discard the packing materialGND Location of EMI core Sectional viewEMI core, putting into core case How to pass the rotation detector cableAntenna unit, clamping the rotation detector cable Mounting the optional mounting bracketHow to assemble and mount the optional mounting bracket Antenna unit Mounting the Antenna Unit of MODEL1833C-BBAntenna unit, inside view How to fasten the radome base to the mounting platformWiring and final preparation Antenna unit, cover removedRF unit Signal cable, antenna unit sideHow to position the radome cover How to attach EMI coreMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator bracket to the antenna unit chassis Fastening the radiator to the radiator bracketCoating the antenna with silicone sealant Antenna unit Location of rubber matFixing the antenna unit chassis How to fasten antenna unit to mounting platformGround Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housingAntenna unit chassis, cover opened Passing the signal cable through the cable gland assemblyHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Power supply unit Mounting the Power Supply Unit of MODEL1953C-BBDesktop mount Mounting the Memory Card Interface UnitStandard Wiring WiringDJ-1 Waterproofing cap and connector nut, sectional viewConnecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portPower supply unit, cover removed Wiring of Power Supply Unit MODEL1953C-BB onlyReplacement of the fuse HUB Connection of CU-200Installation setup menu How to Access the Installation MenuHow to access the Installation menu Host name window Network Setup MenuNetwork setup menu NavNet equipment default settings Contents of Network setup menuRadar setup menu Radar Setup MenuAntenna Type Power supply unit, cover removedExamples of improper and correct sweep timing Tuning setup menuVideo adjustment setting window Timing adjust setting menuTiming adjustment setting display Heading adjustment setting display Heading AdjustmentRadar antenna height setting window Main bung suppression setting windowHeading data setting window STC curve setting windowNavigation Data Source Nav setup menuChecking Magnetron Heater Voltage Position Source Furuno BB GPS ALL Antenna height window GPS setup menuOn next Contents of GPS sensor settings menuContents of GPS sensor settings menu con’t Nmea data sentences Setting up Data PortsDATA1, DATA2 Port menus Contents of Data 1 and DATA2 Port menus Remote System Setting Processor unit cover removed External Buzzer ConnectionExternal buzzer Name Type Code No Qty ARP-11 contentsARP Kit ARP-11 Necessary parts19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page Packing List 付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar
Related manuals
Manual 252 pages 38.1 Kb