Furuno 1943C-BB, 1953C-BB, 1933C-BB, 1823C-BB, 1833C-BB manual Single-unit NavNet system GD-1900C-BB

Page 8

Single-unit NavNet system (GD-1900C-BB)

GPS receiver

GP-310B/320B

Control unit

Processor unit

 

RPU-014

 

RCU-017

 

 

 

 

A

 

 

 

B

 

 

 

C

 

POWER

 

 

 

 

D

 

 

SLAVE DISPLAY

E

 

 

 

 

 

OUTPUT

 

 

 

12 VDC

 

Memory card

 

NTSC/PAL

 

 

OPTION

 

 

 

RGB OUT

 

 

 

 

DJ-1

interface unit CU-200

CARD SLOT

NETWORK CONT DATA 3 DATA 2 DATA 1

 

 

INPUT

 

 

12-24 VDC

 

Other NavNet system

(Model 1833C-BB, etc.)

Monitor (Owner supply)

Plotter, etc.

Rectifier

PR-62

Facsimile

Receiver

FAX-30

:Standard

:Option

Network

Sounder

ETR-6/10N

ETR-30N

12 - 24 VDC

100/110/115/220/230 VAC 1φ , 50/60 Hz

Single-unit NavNet system (GD-1900C-BB)

Note: The output signal from the processor unit for a monitor is as follows.

RGB signal: Analog 0.7 Vpp, Output impedance 75 Ω

Synchro signal: H 31.5 kHz, V 60Hz (Separate), TLL level (VGA signal)

Choose a monitor whose aspect ratio is 4:3, for example, VGA, SVGA, XGA, SXGAX, VXGA, QXGA, etc

vi

Image 8
Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting Flush mounting of display unitDesktop mounting Desktop mounting of display unitProcessor unit, mounting dimensions Mounting the Processor UnitTypical antenna unit placement on sailboat and powerboat Mounting the Antenna Unit of MODEL1823C-BBHow to fasten the mounting base to platform Antenna unit, showing location of mounting hardwareSnap holder Remove and discard the packing material Antenna unit, inside viewGND Sectional view Location of EMI coreHow to pass the rotation detector cable EMI core, putting into core caseMounting the optional mounting bracket Antenna unit, clamping the rotation detector cableHow to assemble and mount the optional mounting bracket Mounting the Antenna Unit of MODEL1833C-BB Antenna unitHow to fasten the radome base to the mounting platform Wiring and final preparationAntenna unit, cover removed Antenna unit, inside viewSignal cable, antenna unit side RF unitHow to attach EMI core How to position the radome coverMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator bracket to the antenna unit chassis Fastening the radiator to the radiator bracketCoating the antenna with silicone sealant Location of rubber mat Antenna unitHow to fasten antenna unit to mounting platform Fixing the antenna unit chassisGround Using inside fixing holes of the antenna housing Antenna unit chassis, upper chassis separatedPassing the signal cable through the cable gland assembly Antenna unit chassis, cover openedHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting the Power Supply Unit of MODEL1953C-BB Power supply unitMounting the Memory Card Interface Unit Desktop mountWiring Standard WiringWaterproofing cap and connector nut, sectional view DJ-1Connecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portWiring of Power Supply Unit MODEL1953C-BB only Power supply unit, cover removedReplacement of the fuse Connection of CU-200 HUBInstallation setup menu How to Access the Installation MenuHow to access the Installation menu Host name window Network Setup MenuNetwork setup menu Contents of Network setup menu NavNet equipment default settingsRadar Setup Menu Radar setup menuPower supply unit, cover removed Antenna TypeTuning setup menu Examples of improper and correct sweep timingVideo adjustment setting window Timing adjust setting menuTiming adjustment setting display Heading Adjustment Heading adjustment setting displayMain bung suppression setting window Radar antenna height setting windowSTC curve setting window Heading data setting windowNavigation Data Source Nav setup menuChecking Magnetron Heater Voltage Position Source Furuno BB GPS ALL GPS setup menu Antenna height windowContents of GPS sensor settings menu On nextContents of GPS sensor settings menu con’t Nmea data sentences Setting up Data PortsDATA1, DATA2 Port menus Contents of Data 1 and DATA2 Port menus Remote System Setting Processor unit cover removed External Buzzer ConnectionExternal buzzer ARP-11 contents ARP Kit ARP-11Necessary parts Name Type Code No Qty19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page Packing List 付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar
Related manuals
Manual 252 pages 38.1 Kb