Furuno 1953C-BB, GD-1900C-BB, 1943C-BB, 1933C-BB manual Model 1823C-BB Model 1833C-BB

Page 67

A-1

MODEL 1823C-BB

MODEL 1833C-BB

Image 67

Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting of display unit Flush mountingDesktop mounting of display unit Desktop mountingMounting the Processor Unit Processor unit, mounting dimensionsMounting the Antenna Unit of MODEL1823C-BB Typical antenna unit placement on sailboat and powerboatAntenna unit, showing location of mounting hardware How to fasten the mounting base to platformAntenna unit, inside view Snap holder Remove and discard the packing materialGND Location of EMI core Sectional viewEMI core, putting into core case How to pass the rotation detector cableAntenna unit, clamping the rotation detector cable Mounting the optional mounting bracketHow to assemble and mount the optional mounting bracket Antenna unit Mounting the Antenna Unit of MODEL1833C-BBAntenna unit, inside view How to fasten the radome base to the mounting platformWiring and final preparation Antenna unit, cover removedRF unit Signal cable, antenna unit sideHow to position the radome cover How to attach EMI coreMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Coating the antenna with silicone sealant Fastening the radiator to the radiator bracketFastening the radiator bracket to the antenna unit chassis Antenna unit Location of rubber matFixing the antenna unit chassis How to fasten antenna unit to mounting platformGround Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housingAntenna unit chassis, cover opened Passing the signal cable through the cable gland assemblyHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Power supply unit Mounting the Power Supply Unit of MODEL1953C-BBDesktop mount Mounting the Memory Card Interface UnitStandard Wiring WiringDJ-1 Waterproofing cap and connector nut, sectional viewConnecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portPower supply unit, cover removed Wiring of Power Supply Unit MODEL1953C-BB onlyReplacement of the fuse HUB Connection of CU-200How to access the Installation menu How to Access the Installation MenuInstallation setup menu Network setup menu Network Setup MenuHost name window NavNet equipment default settings Contents of Network setup menuRadar setup menu Radar Setup MenuAntenna Type Power supply unit, cover removedExamples of improper and correct sweep timing Tuning setup menuTiming adjustment setting display Timing adjust setting menuVideo adjustment setting window Heading adjustment setting display Heading AdjustmentRadar antenna height setting window Main bung suppression setting windowHeading data setting window STC curve setting windowChecking Magnetron Heater Voltage Nav setup menuNavigation Data Source Position Source Furuno BB GPS ALL Antenna height window GPS setup menuOn next Contents of GPS sensor settings menuContents of GPS sensor settings menu con’t DATA1, DATA2 Port menus Setting up Data PortsNmea data sentences Contents of Data 1 and DATA2 Port menus Remote System Setting External buzzer External Buzzer ConnectionProcessor unit cover removed Name Type Code No Qty ARP-11 contentsARP Kit ARP-11 Necessary parts19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page ＰａｃｋｉｎｇＬｉｓｔ付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar

Related manuals

Manual 252 pages 38.1 Kb