Furuno GD-1900C-BB, 1953C-BB, 1943C-BB, 1933C-BB, 1823C-BB manual Radar Setup Menu, Radar setup menu

Page 48

3.3 RADAR SETUP Menu

After setting up the network, do the following in order to adjust the radar.

Open the INSTALL SETUP menu, and then press the B: RADAR SETUP soft key to display the RADAR SETUP menu. When the message “RADAR DOES NOT TRANSMIT. TRANSMIT RADAR?” appears, press the [ENTER] knob to transmit or [CLEAR] key to cancel transmitting.

ANTENNA TYPE

HEADING DATA ANTENNA ROTATION TUNING

TIMING ADJUST

VIDEO ADJUST M.B. SUPPRESSION RADAR ANTENNA HEIGHT STC CURVE

MONITOR MODE

RADAR

FSETUP MAGNETIC

ROTATE A EDIT OFF

OFF

OFF

OFF

D NEXT

HIGHPAGE NARROW

OFF

E RETURN

Page 1

HEADING ADJUST TOTAL ON TIME TOTAL TX TIME

RADAR

OFF SETUP

000000.0 h

000000.0 h

A EDIT

PREV.

E PAGE

Page 2

Radar setup menu

3-4

Image 48
Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting Flush mounting of display unitDesktop mounting Desktop mounting of display unitProcessor unit, mounting dimensions Mounting the Processor UnitTypical antenna unit placement on sailboat and powerboat Mounting the Antenna Unit of MODEL1823C-BBHow to fasten the mounting base to platform Antenna unit, showing location of mounting hardwareSnap holder Remove and discard the packing material Antenna unit, inside viewGND Sectional view Location of EMI coreHow to pass the rotation detector cable EMI core, putting into core caseMounting the optional mounting bracket Antenna unit, clamping the rotation detector cableHow to assemble and mount the optional mounting bracket Mounting the Antenna Unit of MODEL1833C-BB Antenna unitHow to fasten the radome base to the mounting platform Wiring and final preparationAntenna unit, cover removed Antenna unit, inside viewSignal cable, antenna unit side RF unitHow to attach EMI core How to position the radome coverMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator to the radiator bracket Coating the antenna with silicone sealantFastening the radiator bracket to the antenna unit chassis Location of rubber mat Antenna unitHow to fasten antenna unit to mounting platform Fixing the antenna unit chassisGround Using inside fixing holes of the antenna housing Antenna unit chassis, upper chassis separatedPassing the signal cable through the cable gland assembly Antenna unit chassis, cover openedHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting the Power Supply Unit of MODEL1953C-BB Power supply unitMounting the Memory Card Interface Unit Desktop mountWiring Standard WiringWaterproofing cap and connector nut, sectional view DJ-1Connecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portWiring of Power Supply Unit MODEL1953C-BB only Power supply unit, cover removedReplacement of the fuse Connection of CU-200 HUBHow to Access the Installation Menu How to access the Installation menuInstallation setup menu Network Setup Menu Network setup menuHost name window Contents of Network setup menu NavNet equipment default settingsRadar Setup Menu Radar setup menuPower supply unit, cover removed Antenna TypeTuning setup menu Examples of improper and correct sweep timingTiming adjust setting menu Timing adjustment setting displayVideo adjustment setting window Heading Adjustment Heading adjustment setting displayMain bung suppression setting window Radar antenna height setting windowSTC curve setting window Heading data setting windowNav setup menu Checking Magnetron Heater VoltageNavigation Data Source Position Source Furuno BB GPS ALL GPS setup menu Antenna height windowContents of GPS sensor settings menu On nextContents of GPS sensor settings menu con’t Setting up Data Ports DATA1, DATA2 Port menusNmea data sentences Contents of Data 1 and DATA2 Port menus Remote System Setting External Buzzer Connection External buzzerProcessor unit cover removed ARP-11 contents ARP Kit ARP-11Necessary parts Name Type Code No Qty19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page Packing List 付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar
Related manuals
Manual 252 pages 38.1 Kb