Furuno 1933C-BB, GD-1900C-BB, 1953C-BB, 1943C-BB, 1823C-BB GPS setup menu, Antenna height window

Page 57

LOCAL TIME OFFSET

+00:00

GPS

 

 

SETUP

 

GEODETIC DATUM

WGS-84

 

 

 

POSITION SMOOTHING

000 second(s)

A EDIT

 

SPD/CSE SMOOTHING

005 second(s)

 

 

 

 

GPS SPEED AVERAGE

060 second(s)

B

GPS

 

LATITUDE OFFSET

0.000’N

 

STATUS

 

LONGITUDE OFFSET

0.000’E

 

WAAS

For GP-320B,

DISABLE SATELLITE

- - - - - -

C

See operator’s

SETUP

LATITUDE

45° 35.000’ N

 

 

manual

 

 

 

LONGITUDE

125° 00.000’ W

 

 

 

ANTENNA HEIGHT

005 m

E RETURN

 

GPS FIX MODE

2D/3D

 

 

 

 

COLD START

NO

 

 

 

GPS setup menu

e)Select LOCAL TIME OFFSET and press the A: EDIT soft key.

f)Enter time difference between local time and UTC time. Use the A: + < - -> - soft key to

switch from plus to minus and vice versa. Press the C: ENTER soft key.

g)Select ANTENNA HEIGHT and press the A: EDIT soft key.

ANTENNA HEIGHT

005 m

Antenna height window

h)Enter the height of the GP-310B/320B antenna unit above sea surface. Use the trackball to select digit and press the alphanumeric keys to set value. The default height is 5 m.

i)Press the C: ENTER soft key.

j)Choose and set other items as appropriate, referring to the table on the next page.

3-13

Image 57
Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting of display unit Flush mountingDesktop mounting of display unit Desktop mountingMounting the Processor Unit Processor unit, mounting dimensionsMounting the Antenna Unit of MODEL1823C-BB Typical antenna unit placement on sailboat and powerboatAntenna unit, showing location of mounting hardware How to fasten the mounting base to platformAntenna unit, inside view Snap holder Remove and discard the packing materialGND Location of EMI core Sectional viewEMI core, putting into core case How to pass the rotation detector cableAntenna unit, clamping the rotation detector cable Mounting the optional mounting bracketHow to assemble and mount the optional mounting bracket Antenna unit Mounting the Antenna Unit of MODEL1833C-BBWiring and final preparation How to fasten the radome base to the mounting platformAntenna unit, cover removed Antenna unit, inside viewRF unit Signal cable, antenna unit sideHow to position the radome cover How to attach EMI coreMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator to the radiator bracket Coating the antenna with silicone sealantFastening the radiator bracket to the antenna unit chassis Antenna unit Location of rubber matFixing the antenna unit chassis How to fasten antenna unit to mounting platformGround Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housingAntenna unit chassis, cover opened Passing the signal cable through the cable gland assemblyHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Power supply unit Mounting the Power Supply Unit of MODEL1953C-BBDesktop mount Mounting the Memory Card Interface UnitStandard Wiring WiringDJ-1 Waterproofing cap and connector nut, sectional viewConnecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portPower supply unit, cover removed Wiring of Power Supply Unit MODEL1953C-BB onlyReplacement of the fuse HUB Connection of CU-200How to Access the Installation Menu How to access the Installation menuInstallation setup menu Network Setup Menu Network setup menuHost name window NavNet equipment default settings Contents of Network setup menuRadar setup menu Radar Setup MenuAntenna Type Power supply unit, cover removedExamples of improper and correct sweep timing Tuning setup menuTiming adjust setting menu Timing adjustment setting displayVideo adjustment setting window Heading adjustment setting display Heading AdjustmentRadar antenna height setting window Main bung suppression setting windowHeading data setting window STC curve setting windowNav setup menu Checking Magnetron Heater VoltageNavigation Data Source Position Source Furuno BB GPS ALL Antenna height window GPS setup menuOn next Contents of GPS sensor settings menuContents of GPS sensor settings menu con’t Setting up Data Ports DATA1, DATA2 Port menusNmea data sentences Contents of Data 1 and DATA2 Port menus Remote System Setting External Buzzer Connection External buzzerProcessor unit cover removed ARP Kit ARP-11 ARP-11 contentsNecessary parts Name Type Code No Qty19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page Packing List 付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar
Related manuals
Manual 252 pages 38.1 Kb