Furuno 1943C-BB, GD-1900C-BB, 1953C-BB, 1933C-BB, 1823C-BB manual Position Source Furuno BB GPS ALL

Page 56

2.Select POSITION SOURCE and then press the A: EDIT soft key to show the position source window.

POSITION SOURCE

§°￿

FURUNO BB GPS

GP

LC

ALL

3.Select FURUNO BB GPS, GP, LC or ALL as appropriate and press the C: ENTER soft key.

FURUNO BB GPS: GPS Receiver GP-310B/320B

GP: GPS navigator (via NETWORK, DATA 1, or DATA2 connector)

LC: Loran C (via NETWORK, DATA 1, or DATA 2 connector)

ALL: Multiple navaid connection (via NETWORK, DATA 1, or DATA 2 connector)

4.For GPS receiver other than the GP-310B/320B, you may adjust speed averaging and use local time.

a)Choose desired item and press the A: EDIT soft key.

b)Use the trackball to select location and rotate the [ENTER] knob to set value. For time, use the A:+< - -> - soft key to switch from plus to minus and vice versa.

c)Press the C: ENTER soft key.

Speed Averaging: Calculation of ETA is based on average ship’s speed over a given period. If the period is too long or too short calculation error will result. Change this setting if calculation error occurs. The default setting, 60 seconds, is suitable for most conditions. The range of adjustment is 0-9999 (sec).

Local Time Offset: GPS uses UTC time. If you would rather use local time, enter the time difference between it and UTC. The range of offset is –13:30 to +13:30 and the default setting is zero (no offset). Adjustment of this setting is not necessary if the time difference has been entered at the GPS navaid connected to the NavNet.

Temp Calibration: Offsets NMEA water temperature data (-40°F to +40°F).

Depth Calibration: Offsets NMEA depth data (-15 ft to +90 ft).

5.For GP-310B/320B,press the E: RETURN soft key twice to show the SYSTEM CONFIG menu.

a)Press the C: SYSTEM SETUP soft key followed by A: PORT SETUP and A: GPS/NMEA PORT soft keys. When the GP-310B/320B is connected to the DATA 2 port, press the B: NMEA PORT soft key.

b)Select FURUNO GPS SENSOR, and press the A: EDIT soft key to show FURUNO GPS SENSOR window.

c)Select YES and press the C: ENTER soft key.

d)Press the E: RETURN soft key three times followed by B: NAV OPTIONS, B: GPS SENSOR SETTINGS soft keys to show the GPS SETUP menu.

3-12

Image 56
Contents Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BBThree-or-more-unit NavNet system Three-or-more-unit NavNet systemTwo-unit NavNet system Two-unit NavNet systemMounting Flush mounting Flush mounting of display unitDesktop mounting Desktop mounting of display unitProcessor unit, mounting dimensions Mounting the Processor UnitTypical antenna unit placement on sailboat and powerboat Mounting the Antenna Unit of MODEL1823C-BBHow to fasten the mounting base to platform Antenna unit, showing location of mounting hardwareSnap holder Remove and discard the packing material Antenna unit, inside viewGND Sectional view Location of EMI coreHow to pass the rotation detector cable EMI core, putting into core caseMounting the optional mounting bracket Antenna unit, clamping the rotation detector cableHow to assemble and mount the optional mounting bracket Mounting the Antenna Unit of MODEL1833C-BB Antenna unitHow to fasten the radome base to the mounting platform Wiring and final preparationAntenna unit, cover removed Antenna unit, inside viewSignal cable, antenna unit side RF unitHow to attach EMI core How to position the radome coverMounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator bracket to the antenna unit chassis Fastening the radiator to the radiator bracketCoating the antenna with silicone sealant Location of rubber mat Antenna unitHow to fasten antenna unit to mounting platform Fixing the antenna unit chassisGround Using inside fixing holes of the antenna housing Antenna unit chassis, upper chassis separatedPassing the signal cable through the cable gland assembly Antenna unit chassis, cover openedHow to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting the Power Supply Unit of MODEL1953C-BB Power supply unitMounting the Memory Card Interface Unit Desktop mountWiring Standard WiringWaterproofing cap and connector nut, sectional view DJ-1Connecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 portWiring of Power Supply Unit MODEL1953C-BB only Power supply unit, cover removedReplacement of the fuse Connection of CU-200 HUBInstallation setup menu How to Access the Installation MenuHow to access the Installation menu Host name window Network Setup MenuNetwork setup menu Contents of Network setup menu NavNet equipment default settingsRadar Setup Menu Radar setup menuPower supply unit, cover removed Antenna TypeTuning setup menu Examples of improper and correct sweep timingVideo adjustment setting window Timing adjust setting menuTiming adjustment setting display Heading Adjustment Heading adjustment setting displayMain bung suppression setting window Radar antenna height setting windowSTC curve setting window Heading data setting windowNavigation Data Source Nav setup menuChecking Magnetron Heater Voltage Position Source Furuno BB GPS ALL GPS setup menu Antenna height windowContents of GPS sensor settings menu On nextContents of GPS sensor settings menu con’t Nmea data sentences Setting up Data PortsDATA1, DATA2 Port menus Contents of Data 1 and DATA2 Port menus Remote System Setting Processor unit cover removed External Buzzer ConnectionExternal buzzer ARP-11 contents ARP Kit ARP-11Necessary parts Name Type Code No Qty19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page Packing List 付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar
Related manuals
Manual 252 pages 38.1 Kb