Xantrex Technology Freedom SW 2000 user service Materials List

Page 16

Introduction

Materials List

The Freedom SW 2000 ships with the following items:

•one Freedom SW 2000 unit,

•owner’s and installation guides,

•Battery Temperature Sensor (BTS),

•Freedom SW remote panel with 25-foot communications cable,

•DC terminal covers (one red, one black) with two sets of screws, and

•two sets of nuts and washers for the DC terminals.

NOTE: If any of the items are missing, contact Xantrex or any authorized Xantrex dealer for replacement. See “Contact Information” on page i.

IMPORTANT: Keep the carton and packing material in case you need to return the Freedom SW 2000 for servicing.

Fault

Batt %

FREEDOM		SW
		SW
kW	Inverting	2000
	Inverting	2000
A	Charging
	Charging
		FREEDOM	SW
			SW	2000
				2000

Installation and

Owner’s Guides

Freedom SW 2000

Remote panel with	BTS
communications cable

DC terminal covers	nuts and washers
with screws

Figure 1 Materials List

2	Freedom SW 2000 Installation Guide

Image 16

Contents Freedom SW Sine Wave Inverter/Charger Page This guide for use by qualified installers only About This Guide Statement of HazardRelated Information Important Safety Instructions Electrical Shock HazardFire and Burn Hazard Explosion HazardPrecautions When Working With Batteries Exposure to Chemicals and Gases Hazard Precautions When Preparing to ChargeRisk of Damage to the INVERTER/CHARGER Regulatory Limitations on USEContents Page Cabling and Hook-up Configurations Page Introduction Materials List Materials ListInstallation Information Before You Begin the InstallationInstallation Codes Electrical Shock and Fire HazardsPlanning the Installation Two Key Performance FactorsSize and Length of DC Cables Mounting Location of the Freedom SWAC and DC Components including wire and breaker sizes Sample Vehicle Electrical System ConfigurationFor wire and breaker size information AC Components AC InputAC Output AC LoadsDistribution Panels AC Output ProtectionGfci Requirements Tested GFCIsAC Wiring AC Output Neutral BondingBatteries DC ComponentsDC Disconnects and Over-Current Devices DC Cabling DC GroundingHeavy Load Tools Installation Tools and MaterialsMaterials Installing the Inverter/Charger OverviewFire and Explosion Hazard Choosing a Location for the Inverter/ChargerHeat Hazard Battery Battery acidSafe Close toConsiderations Mounting the Inverter/ChargerTo mount the inverter/charger Approved Mounting Orientation Orientation? Comment Approved Mounting Orientation Orientation? General AC Wiring Considerations Connecting the AC Input and AC Output WiresFIRE, Electrical SHOCK, and Energy Hazards Connecting AC Input Wires Equipment DamageDamage other equipment To make the AC input connectionsConnecting AC Output Wires Output AC Wire Size Connecting the DC Cables DC Connection PrecautionsPreparing the Cables To prepare the DC cablesGuidelines for Routing the DC Cables Electrical Shock and Fire HazardFire Hazard Connecting the DC Cables to the Inverter/ChargerEquipment Damage DUE to Reverse Polarity DC Terminal Covers 2000 To connect the chassis groundConnecting the Battery Temperature Sensor BTS Mounting OptionsMounting to the Negative Battery Terminal To mount the sensor on the negative battery terminalConnecting the BTS Cable to BTS Jack Mounting to the Side of the Battery Case To mount the sensor on the battery casePerforming Checks Prior to Initial Start-Up Testing Your Installation Testing in Invert ModeTesting in Charge Mode Installation CompleteInverter/Charger Physical Specifications Battery Information Battery Bank SizingCalculating Battery Size Calculate Battery SizeBattery Information Battery Bank Sizing Worksheet Battery BanksRestrictions on Motor Size = Total watt-hours of AC load between charges Cabling and Hook-up Configurations Parallel ConnectionSeries Connection Batteries Connected in SeriesSeries-Parallel Connections Batteries in Series-Parallel ConnectionsPage Page Xantrex Technology Inc