Sierra
830, 860, 840
instruction manual
Appendix B Specifications IM-83/84/86-H
Troubleshooting
Specifications
Install
Output Signal Connections
Wiring the Transducer
Dimension
Maintenance
Pin Connector Pin Designations
NPT Transducer LFE Cleaning
Safety
Page 71
Appendix B Specifications
Series 830/840/860 Instruction Manual
B-8
IM-83/84/86-H
Page 70
Page 72
Image 71
Page 70
Page 72
Contents
Table of Contents
Customer Notice
Table of Contents
Table of Contents
Troubleshooting
List of Tables
Table of Contents
Introduction
Using This Manual
Introduction
Technical Assistance
Safety Information
Receipt of System Components
Flow Paths through the Transducer
Series 800 Flow Sensing Principle
Sensor Temperature Distribution
Installation
Installation Overview
VCO Fittings
Installing the Transducer
Compression Fittings
NPT Fittings and 1/2-Inch Connections All Types
VCR Fittings
Recommended Wire Gauges
Wiring the Transducer
Recommended Wire Gauges
Output Signal Connections
Wiring Transducers with 20-Pin Card-Edge Connectors Input
Input Signal Connections Controllers Only
Depending on the valve voltage, connect as shown below
Valve Purge and Valve Off Connections Controllers Only
Pin Connector Pin Designations
Input Power Connections
Wiring Transducers with 15-Pin D-Connectors
Input Signal Connections Controllers Only
13. Valve Purge and Valve Off 15-Pin D-Connector
15 -Pin D-Connector Pin Assignments
16. Motor-Operated Rotary Valve Connector 10-Pin Connector
Motor-Operated Valve Circular 10-Pin Connector
Mass Flow Meter Operation
Operation
Electromagnetic Valve Controllers
Mass Flow Controller Operation
Motor-Operated Rotary Valve Controllers
Over-Range and Cold Sensor Lockout Circuit
Mass Flow Controller Features
Controller Auto Shut-Off Feature
Soft Start Response Times
On-Off Control and Soft Start Option
Purging Reactive Gases
Valve Purge Function
Purging Non-Reactive Gases
Operation
Cleaning the Laminar Flow Element
Flow Path Maintenance
Low Flow Transducers
Low Flow Transducer LFE Cleaning
Medium Flow Transducers
Medium Flow Transducer LFE Cleaning
High Flow Transducers
High Flow Transducer LFE Cleaning
NPT-Type Transducers
NPT Transducer LFE Cleaning
Sensor Cleaning and Inspection
Sensor Maintenance
Sensor Electrical Test
Electromagnetic Valves Low and Medium Flow Controllers
Valve Maintenance
Electromagnetic Valves High Flow Controllers
Maintenance
Motor-Operated Rotary Valves
840 L, M and H series Valve Adjustment Procedure
Maintenance
Maintenance
Transducer Calibration
Troubleshooting
Flow Meters and Flow Controllers with Electromagnetic Valves
Valve rotates continuously
Flow Controllers with Motor-operated Rotary Valves
Factory Calibration-All Models
Instructions for Returning Your Instrument for Service
Return Address
Example 2 Finding the Actual Flow Rate
Conversion of Flow Rate to Other T and P Conditions
Example 1 Changing Standard Conditions
14.7 460 + 10.00 = 3.47 lm 14.7 +
Calculating For a Single Gas
880
Example
Important Note about K-FACTORS
Calculating Dual Gas Mixtures
NEO
Gas Tables and K-factors
C2H6O
CH 3SH
Operating Specifications
Appendix B Product Specifications
VDC
Physical Specifications
Performance Specifications
Valve plug standard Neoprene, 4079 Kal-Rez
Low Flow Body
Transducer Mounting Dimensions
Medium Flow Body
High Flow Body
Appendix B Specifications IM-83/84/86-H
Flow Range, slpm
NPT Flow Body
100 200 Inlet Fnpt
Appendix B Specifications
Top
Page
Image
Contents