Siemens SAMMS-MV Function Number, 5A CT primary current if used Full load current for OLR No

Page 29

3 Operating the SAMMS-MV Device

		SAMMS-MV

Function Number	Function	SAMMS-MVX	SAMMS-MVE

F0	Ambient temperature	∙	∙

F1	Control circuit number	∙	∙

F2	Size for overload No. 1	∙	∙

F3	Size for overload No. 2 (low speed)	∙

F4	Full load current for OLR No. 1	∙	∙

F4A	5A CT primary current (if used)	∙	∙

F5	Full load current for OLR No. 2	∙

F5A	5A CT primary current (low speed) (if used)	∙

F6	Service factor	∙	∙

F6A	Motor type	∙	∙

F7	Overload trip class (class 2 through 23)	∙	∙

F7A	Cold stall time	∙	∙

F8	Automatic reset	∙

F9	Phase unbalance	∙	∙

F10	Time to restart	∙	∙

F11	Emergency restart	∙	∙

F12	Ground fault protection or warning	∙	∙

F12A	Ground fault pickup current	∙	∙

F13	Timer No. 1	∙	∙

F14	Timer No. 2	∙	∙

F15	Motor current	∙	∙

F16	Last trip current	∙	∙

F17	Percent unbalance current	∙	∙

F18	Total elapsed run-time on motor	∙	∙

F19	Total number of motor starts	∙	∙

F20	Number of overload trips	∙	∙

F21	Reset motor data	∙	∙

F22	Set process current warning	∙

F23	Jam protection	∙

F23A	Jam pickup current	∙

F24	Loss of load protection or warning	∙

F24A	Loss of load pickup current	∙

F25	Motor winding temperature as % of full load temperature	∙	∙

F26	Baud rate	∙	∙

F27	Address	∙	∙

Table 3.7 SAMMS-MV models and functions

27

Image 29

Contents SAMMS-MV Qualified Person Contents Qualified Person Signal WordsField Service Operation About this Manual Advanced Protection for Medium-Voltage Motors SAMMS-MV Device ModelsProgramming Control Circuits Using the Standardized Control PanelOverload Protection SAMMS-MV Model Change settings requires password Yes Remote inputs OneOutputs One Light barsInstalling the SAMMS-MV Device Full voltage non-reversing connection diagram Grounding the Device SAMMS-MV device communications connections Using the Reset/Test Push Button Password ProtectionPerforming a Lamp Test Performing an Overload Relay TestInput Devices Output DevicesCustom Ladder Diagrams Ladder Diagrams Library of Standard Ladder DiagramsSAMMS-MVX Standard control circuits PB1 PB2 PB3 PB4 PB5 PB6 Motor Ambient Temperature Ridethrough Upon Loss of Power SAMMS-MVX OnlyIncomplete Sequence Intelligent Reduced-Voltage Starting SAMMS-MVX OnlyODP motor thermal signature Protection Curves and Overload Classes Seconds Operating the SAMMS-MV 11 Motor protection graph Phase Unbalance Ultimate Trip Level and Service FactorDual Overload Protection SAMMS-MVX Only Jam Protection SAMMS-MVX OnlyRepetitive Starts Ground Fault DetectionStart Inhibit Cooling Time Constants12 Multi-start scenario for an ODP motor Using the Hand Held Communicator HHC Autoreset After a Trip SAMMS-MVX OnlyEmergency Restarting Function KeyFunction Number 5A CT primary current low speed if used Service factor5A CT primary current if used Full load current for OLR No Motor type Overload trip class class 2 throughUP and Down Keys Using the Enter KeyUsing the SAMMS-MV Device Func- tions ON/OFF Default Value Select ground fault pick-up currentMeans warning Select jam pickup current 120-400% Iflc F24 Loss of Load13 Entering and changing passwords F0 Ambient Temperature Program Mode/PasswordsSAMMS-MV Functions F1 Control Circuit Number and Incomplete Se- quence StatusF3 Size for Overload Relay #2 SAMMS-MVX Only Overload Setting Step Default Relay Size RangeF4 Full-Load Current for Overload Relay #1 18 to 72AF6A Motor Type F6 Service FactorF7 Overload Trip Class F7A Cold Stall TimeF9 Phase Unbalance Protection F8 Autoreset SAMMS-MVX OnlyF10 Display Time to Restart F11 Emergency RestartingF12A Ground Fault Pickup Current F12 Ground Fault Protection or WarningSize Pickup Current Default H3A-H3C 7A-I FLC 10A 20A F13 Set Programmable Timer #1F16 Trip Current F21 Reset Motor DataF17 Current Unbalance F18 Display Total Elapsed Run Time of the MotorF22 Process Current Warning Level SAMMS-MVX Only F25 Percentage of Motor Winding TemperatureF23 Jam Protection SAMMS-MVX Only F23A Jam Pickup Current SAMMS-MVX OnlyF27 Address F26 Baud RateTroubleshooting Error Condition Troubleshooting Guide Error Condition Appendix a Technical Specifications Over load Spec ificat ions Stat ist ica l Data Dimensions Catalog Number SAM6 Switch # Function Position 375 Siemens Energy Automation, Inc