Furuno GP-7000F Vertical adjustment and cable routing, Attaching the sensor to the bracket

Page 22

5.Using the vertical adjustment space on the bracket slots, slide the sensor up or down to pro- vide a projection of 3 mm (1/8"). Tighten the screws.

Cable cover

Cable clamp

50 mm (2")

Hull projection 3 mm (1/8")

Vertical adjustment and cable routing

Attaching the sensor to the bracket

1.If the retaining cover near the top of the bracket is closed, open it by depressing the latch and rotating the cover downward.

Step 1

Step 2

 

Latch

Step 3

Pivot

Step 4

arm (2)

 

Retaining

 

cover

Slot (2)

Attaching the sensor to the bracket

2.Insert the sensor's pivot arms into the slots near the top of the bracket.

3.Maintain pressure until the pivot arms click into place.

4.Rotate the sensor downward until the bottom snaps into the bracket.

5.Close the retaining cover to prevent the accidental release of the sensor when the boat is underway.

Cable routing

Route the sensor cable over the transom, through a drain hole, or through a new hole drilled in the transom above the waterline.

Never cut the cable or remote the connector; this will void the warranty. Always wear safety gog- gles and a dust mask.

1.If a hole must be drilled, choose a location well above the waterline. Check for obstructions such as trim tabs, pumps, or wiring inside the hull. Mark the location with a pencil. Drill a hole through the transom using a 19 mm or 3/4" bit (to accommodate the connector).

2.Route the cable over or through the transom.

3.On the outside of the hull secure the cable against the transom using the cable clamps. Posi- tion a cable clamp 50 mm (2") above the bracket and mark the mounting hole with a pencil.

16

Image 22
Contents Color GPS/PLOTTER/SOUNDER GP-7000F Iii00014914012 Safety Instructions System Configuration Standard supply Name Type Code No Qty RemarksOptional equipment Name Type Code No QtyDisplay Unit Mounting considerationsMounting Desktop, overhead mountingFlush mounting Antenna Unit Inside-hull mounting Remarks on installationTransducer Necessary toolsCoating transducer face with silicone sealant Attaching the transducerFinal preparations Squeezing out air bubbles in adhesiveThru-hull mounting Thru-hull mount transducer mounting dimensions millimetersTransducer mounting location Acceptable transducer mounting locations Suitable transducer mounting locationsConstruction of fairing block Procedure for installing the thru-hull mount transducerTransducer mounting Installing the transom mount transducer on a flat hull Transom mount transducerInstalling the transom mount transducer on a deep-V hull Transducer preparationOptional triducer Triducer 525ST-MSDHeight required at mounting location Mounting location on single drive boatInstallation template Sensor position and transom angle Vertical adjustment and cable routing Attaching the sensor to the bracketPage Optional Speed/Water Temperature Sensor ST-02MSB, ST-02PSB Speed/water temperature sensor ST-02MSB, ST-02PSBWiring Power source TransducerGround Antenna cable Connecting the antenna cableAntenna Code no Contents Cable set Types of antenna cablesWaterproofing the connector How to attach N-P-8DFB connector for extension cable kit Fabricating the transducer cable Optional transducerPart Type Code No Qty Remarks Adjustments Choosing Position Data SourceINPUT/OUTPUT menu Input Choosing Port I/O FormatNmea 1 INPUT, Nmea 1 Output menus Description of Nmea optionsInput data, sentence priority OutputFormat Port Format Data sentence RemarksOutput Power Transducer Echo Sounder SettingsSetting transducer model, output power Echo Sounder System Setup menuSensor Setup menu Calibrating speed/water temperature sensor, setting draftEcho Sounder menu Setting range Choosing Data SourcesSetting range Calibrating Nmea Depth, Speed and Water Temperature DataEXT Nmea menu Waypoint, Route Format External Event FormatPrimary, Secondary Unit C-link Packing List GP-7000/F-E-C-017,GP-7000/F-E-N-017 Packing List GP-7000/F-E-C,GP-7000/F-E-N Page Page Hatai Mar,2707 R.Esumi Feb Page Page Page 指示部 Display Unit GP-7000F