Furuno GP-7000F installation manual Primary, Secondary Unit C-link

Page 41

3.8Primary, Secondary Unit (C-link)

The C-link feature, available when several GP-7000 series units are interconnected via NMEA ports or PC/NMEA IN ports (see the illustration below), lets you duplicate on secondary stations the destination set at the primary station. With this feature active destination may only be set from the primary station.

Primary station

GP-7000 NMEA1

seriesNMEA2

PC/NMEA IN

Secondary station

GP-7000 NMEA1

seriesNMEA2

PC/NMEA IN

Secondary station

GP-7000 NMEA1

seriesNMEA2

PC/NMEA IN

Secondary station

GP-7000 NMEA1

seriesNMEA2

PC/NMEA IN

*

*

*: Either port

**: Either port

**

**

Note: Secondary stations cannot be connected to one another.

1.Press the [MENU] key to show the menu bar.

2.Rotate the [ENTER] knob to choose ADVANCED from the menu bar and then push the [ENTER] knob.

3.Rotate the [ENTER] knob to choose INPUT/OUTPUT and then push the [ENTER] knob.

4.Rotate the [ENTER] knob to choose C-LINK and then push the [ENTER] knob.

Secondary Station

Primary Station

Off

5.Choose Off, Secondary Station, Primary Station as appropriate and then push the [ENTER] knob.

6.Press the [MENU] key to close the menu.

35

Image 41

Contents Iii Color GPS/PLOTTER/SOUNDER GP-7000F00014914012 Safety Instructions System Configuration Name Type Code No Qty Remarks Standard supplyName Type Code No Qty Optional equipmentMounting considerations Display UnitDesktop, overhead mounting MountingFlush mounting Antenna Unit Transducer Remarks on installationInside-hull mounting Necessary toolsFinal preparations Attaching the transducerCoating transducer face with silicone sealant Squeezing out air bubbles in adhesiveTransducer mounting location Thru-hull mount transducer mounting dimensions millimetersThru-hull mounting Suitable transducer mounting locations Acceptable transducer mounting locationsTransducer mounting Procedure for installing the thru-hull mount transducerConstruction of fairing block Transom mount transducer Installing the transom mount transducer on a flat hullTransducer preparation Installing the transom mount transducer on a deep-V hullTriducer 525ST-MSD Optional triducerMounting location on single drive boat Height required at mounting locationInstallation template Sensor position and transom angle Attaching the sensor to the bracket Vertical adjustment and cable routingPage Speed/water temperature sensor ST-02MSB, ST-02PSB Optional Speed/Water Temperature Sensor ST-02MSB, ST-02PSBWiring Transducer Power sourceGround Antenna Code no Contents Cable set Connecting the antenna cableAntenna cable Types of antenna cablesWaterproofing the connector How to attach N-P-8DFB connector for extension cable kit Part Type Code No Qty Remarks Optional transducerFabricating the transducer cable Choosing Position Data Source AdjustmentsINPUT/OUTPUT menu Nmea 1 INPUT, Nmea 1 Output menus Choosing Port I/O FormatInput Description of Nmea optionsFormat OutputInput data, sentence priority Port Format Data sentence RemarksSetting transducer model, output power Echo Sounder SettingsOutput Power Transducer Echo Sounder System Setup menuEcho Sounder menu Calibrating speed/water temperature sensor, setting draftSensor Setup menu Choosing Data Sources Setting rangeEXT Nmea menu Calibrating Nmea Depth, Speed and Water Temperature DataSetting range External Event Format Waypoint, Route FormatPrimary, Secondary Unit C-link ＰａｃｋｉｎｇＬｉｓｔ GP-7000/F-E-C-017,GP-7000/F-E-N-017 ＰａｃｋｉｎｇＬｉｓｔ GP-7000/F-E-C,GP-7000/F-E-N Page Page Hatai Mar,2707 R.Esumi Feb Page Page Page 指示部 Display Unit GP-7000F