Furuno GP-7000F installation manual Ground

Page 27

MJ-A6SRMD

		SHIELD	1
		TEMP	2
	Speed/Water	TEMP0V/SPD0V	3
	Speed/Water	SPD	4
	Temp.	SPD	4
	Temp.	+V	5
	Sensor	+V	5
		NC	6
		MJ-A10SRMD
		NC	1
		NC	2
		NC	3
		NC	4
	Transducer	NC	5
	Transducer	NC	6
		NC	6
		NC	7
		XDR+	8
		XDR SHIELD	9
		XDR-	10

GP-7000F

MJ-A10SPF

4 TEMP

7 TEMP0V

3 TEMP0V/SHIELD

1SPD

2+12V

5NC

6NC

8XDR+

9XDR-SHIELD

10 XDR-

Wiring for connection of speed/water temperature sensor with cable 02S4147

Ground

Connect the ground wire to the boat's grounding bus. If the unit is not grounded, noise may result. If noise is a problem on an FRP vessel, fasten a ground plate of 20 cm x 30 cm to the outside of the ship's hull and connect the ground wire there.

Use a closed-type lug ( ) for the connection on the display unit. Do not use an open-type lug

( ).

21

Image 27

Contents Iii Color GPS/PLOTTER/SOUNDER GP-7000F00014914012 Safety Instructions System Configuration Name Type Code No Qty Remarks Standard supplyName Type Code No Qty Optional equipmentMounting considerations Display UnitDesktop, overhead mounting MountingFlush mounting Antenna Unit Necessary tools Remarks on installationTransducer Inside-hull mountingSqueezing out air bubbles in adhesive Attaching the transducerFinal preparations Coating transducer face with silicone sealantThru-hull mount transducer mounting dimensions millimeters Thru-hull mountingTransducer mounting location Suitable transducer mounting locations Acceptable transducer mounting locationsProcedure for installing the thru-hull mount transducer Construction of fairing blockTransducer mounting Transom mount transducer Installing the transom mount transducer on a flat hullTransducer preparation Installing the transom mount transducer on a deep-V hullTriducer 525ST-MSD Optional triducerMounting location on single drive boat Height required at mounting locationInstallation template Sensor position and transom angle Attaching the sensor to the bracket Vertical adjustment and cable routingPage Speed/water temperature sensor ST-02MSB, ST-02PSB Optional Speed/Water Temperature Sensor ST-02MSB, ST-02PSBWiring Transducer Power sourceGround Types of antenna cables Connecting the antenna cableAntenna Code no Contents Cable set Antenna cableWaterproofing the connector How to attach N-P-8DFB connector for extension cable kit Optional transducer Fabricating the transducer cablePart Type Code No Qty Remarks Choosing Position Data Source AdjustmentsINPUT/OUTPUT menu Description of Nmea options Choosing Port I/O FormatNmea 1 INPUT, Nmea 1 Output menus InputPort Format Data sentence Remarks OutputFormat Input data, sentence priorityEcho Sounder System Setup menu Echo Sounder SettingsSetting transducer model, output power Output Power TransducerCalibrating speed/water temperature sensor, setting draft Sensor Setup menuEcho Sounder menu Choosing Data Sources Setting rangeCalibrating Nmea Depth, Speed and Water Temperature Data Setting rangeEXT Nmea menu External Event Format Waypoint, Route FormatPrimary, Secondary Unit C-link ＰａｃｋｉｎｇＬｉｓｔ GP-7000/F-E-C-017,GP-7000/F-E-N-017 ＰａｃｋｉｎｇＬｉｓｔ GP-7000/F-E-C,GP-7000/F-E-N Page Page Hatai Mar,2707 R.Esumi Feb Page Page Page 指示部 Display Unit GP-7000F