Furuno RP-250 Controls, FR-2105 series radar display unit, Video plotter controls, AIS controls

Page 8

1. OPERATIONAL OVERVIEW

1.2Controls

Power switch

Control head Card

slot

FR-2105 series radar display unit

POWER

HL

PANEL

MODE

AUDIO

RADAR

PLOT

NAV

OFF

BRILL

OFF

MENU

MENU

MENU

1

2

3

BRILLIANCE

A/C RAIN

A/C SEA

GAIN

OFF

VECTOR

LOST

ON

CENTER

TARGET

4

5

6

OFF PM

ACQ

ANTENNA

CHART

#1

#2

EBL

MARK

ALIGN

STBY

7

TARGET

OFF

ON

ON

8

9

OFF

DATA

TUNE

TX

	EBL	AIS	AIS
DEGAUSS ERROR		DATA	MENU

		TARGET	CU, TM	A/C
RANGE	VRM	TRAILS	RESET	AUTO	TARGET
		CANCEL	0	ENTER	CANCEL

Function set and labels attached at installation

FR-2105 series control head (RP-250-related controls shaded in gray)

Video plotter controls

RADAR MENU:	Open and close the radar menu.
NAV MENU:	Open and close the video plotter menu.
CHART ALIGN:	Align video plotter display with radar display.
MARK:	Enter various marks.
Numeric keys:	Enter data.
ENTER:	Terminate keyboard input.
AIS controls
AIS MENU:	Open AIS menu.
AIS DATA:	Display basic data for selected target.
AUDIO OFF:	Silence AIS-related alarms.
VECTOR:	Alternately display true and relative speed and course vector.

LOST TARGET: Erase AIS lost target marks. (ARPA lost target mark is also erased.)

Note 1: A single beep is produced to signify that the radar has accepted your command. Two beeps sound in case of incorrect key operation.

Note 2: When the NAV MENU key is pressed in the plotter/radar or plotter mode, the message “Chart displayed is for reference only. Position should be confirmed against nautical charts.” appears. Use the electronic chart as an aid to navigation.

2

Image 8

Contents Video Plotter 00080933204 Safety Instructions Table of Contents IN-1 IiiSP-1 Word to the Owner of the RP-250 FeaturesForeword Operational Overview GeneralControls FR-2105 series radar display unitVideo plotter controls AIS controlsChoosing Display Mode Video plotter displayAbout the radar/video plotter display Choosing Presentation ModeItem and default setting Default selected at above Charts Displaying a chartChart, cursor position correction Chart position correctionSetting up the Video Plotter Display Canceling chart position correctionHiding/Showing graphics Cursor position correctionHiding/Showing nav data NAV Information 1 menuNAV Information 3 menu For manual input of position item 4, do the followingNAV Information 2 menu Track Stopping Plotting of Own Ships TrackStopping Plotting of Other Ship’s Track OWN SHIP, Target Plot menuTrack Plotting Interval Choosing track plotting intervalFinding track memory used Memory in USE displayPlotter Erase menu SmoothingErasing Track Target Plot Color menu Own Ship Track ColorOther Ship Track Color MARKS, Lines Choosing Method of EntryEntering Marks/Lines Entering marks/lines at cursor or own ship positionLine change feature Entering marks at desired positionMark/Line Color Erasing Marks/LinesErasing individual marks Erasing all marks and all linesFinding Mark/Line Memory Used WAYPOINTS, Navigation Lines Entering WaypointsEntering waypoints at cursor position Entering waypoints at specific positionWPT List Waypoint ListEntering waypoints at own ship position Displaying Waypoints Displaying waypointsDisplaying waypoints from a navigator Waypoint menuDeleting Waypoints Navigation LinesDeleting individual waypoints Deleting all waypointsAdding waypoints to navigation lines Removing waypoints from navigation linesNav line list Deleting individual navigation linesSetting up navigation lines NAV Line menuBWR Displaying navigation lines Record menu RECORDING, Replaying DataFormatting Memory Cards Replay Card 1 menu Recording DataReplaying Data Other Plotter Functions Initial SettingsVideo PLOTTER, Initial Setting menu Longitude Error Table on 96 nm range scale Distance error in direction of longitude due to latitude2256 4444 6496 8350 9950 1248 2202 2786 2980 This page intentionally left blank Turning AIS Feature On/Off AIS symbolsAIS Operation AIS1 menuActivated target Turning AIS Display On/OffActivating Targets Sleeping Targets Sleeping an AIS targetSleeping all AIS targets Sleeping targetDisplaying Target Data Activating all sleeping AIS targetsBasic target data Activated target selected for data displayExtended target data Extended data displayLost Target MessagesDisplaying messages manually Lost targetSafety related message Automatically displaying messagesHistory Display Turning history display on/offSample history displays AIS2 menuAIS Symbol Color Choosing history display attributesAutomatic Target Activation Lost Target RangeROT Display Setting ROT displayCombining AIS with Arpa fusion AIS3 menuMessage Meaning AIS System MessagesAIS system messages AIS Alarm Message Maintenance Replacing the Battery on the RP BoardReplacing the Battery in the Memory Card Battery for Battery Type Code NumberSystem Error Installation of Video Plotter KIT Tabletop/Console TypeNecessary parts Name Type Qty Code No RemarksControl head Display unitSetting catch to hole in stay Display unit, inside viewStay fixed Fastening the M-card assy. to the right arm coverDisplay pedestal, front view Display pedestal, top viewPC connection TD-BFR-2105 Test Test resultsAIS Data Separate Type Control Head Fasten with M4 x 8 screw Fasten with M3 x 8 screws 2 pcs Installation of Video Plotter KIT Appendix Digital Interface IECInput sentences RP Board, J4 Data receptionSchematic diagram Load requirements as listenerInterface Function COG, SOG, HDG, ROTMain Board Modification IEC 60936-1 related items SOG selected on menu Conditions Which Display the Alarm for WTSTW selected on menu Menu Tree Video plotterEnter WPT, NAV Line OWN SHIP, Target Plot AIS Specifications of Video Plotter RP-250Index IN-1