Revolabs 01-HDEXEC, 03-HDEXECEU Acoustic Cover protects microphone element non-removable

Page 28

If the microphones are placed too far from the Base Station (~300 feet or 91 meters) the connection will be dropped (LED flashes all colors) and the microphone will mute. After 15 seconds the microphone will beep 5 times, and will continue beeping every 30 seconds to indicating it‘s out of range.

Move the microphone closer to the Base Station and the connection will automatically be re- established to its original state, and the beeping will cease. If not, the microphone will continue beeping until it turns off in about 15 minutes.

Using the HD Directional Tabletop Wireless Boundary Microphones

The HD Tabletop Wireless Microphone, shown below, is designed to provide optimum coverage when placed on a conference room table in front of one or two people.

Pickup

45

6

patter

45

 

n

 

 

 

5

 

1

 

 

 

2

3

4

 

 

1.

LED display — visual status for mute, un-mute, and pairing.

2.

Rubber feet — non-slip, vibration absorbing pads.

 

3.

Audio jack — accepts a 2.5mm plug.

 

 

4.

Charging port — docks to Revolabs HD Charger Bases.

5.

Mute button — press to mute, un-mute and pair microphone.

6.

Acoustic Cover — protects microphone element (non-removable).

To use the HD Directional Tabletop Microphone:

13.Remove the microphone from the Charger Base to turn on and automatically mute the mic. (indicated by a flashing RED LED)

14.Directional Tabletop microphones should be located on the table with the acoustic cover pointed toward the users, trying to keep the microphone 2 to 6 feet (0.6 to 2m) from the target person or two. The pick-up pattern for this directional microphone is ~+/- 45º to either side of directly in front of the microphone. It is always better to be as close to the person speaking as possible, but avoid placing the microphone where it might be blocked by equipment or paperwork. Avoid placing microphones too close to an audio or video conference speaker to avoid echoes. Make sure that the microphone is always placed lying on its rubber feet atop a flat surface. Refer to diagram below:

- 28 -

Image 28
Contents Revolabs Executive HD Page Contents Safety and General Information FCC Notice to UsersStandards to which Conformity is declared Introduction System ComponentsInstalling the Revolabs Executive HD Base Station Controls and Connections Using Multiple Revolabs Executive Hdtm Systems Together Configuring the Executive Hdtm Base StationRevolabs Executive HD Audio Connections Primary DIP#1 -off Secondary DIP#1 -on Wire BUS cable Using the Revolabs HD Control Panel Software Using the Rear Panel Configuration DIP SwitchesRevolabs HD Gold Control Panel File Record Events Configuration SettingsSystem Scan Network System Set IP Configuration System Set Telnet PasswordSystem Set Box Name System Enable Gold Firmware Update FirmwareConfig External Control Processor Tools Express PairConfig Audio Mode Config RedundancyConfig Power Scaling Config Transmit PowerConfig Audio Zone Config Lock Front PanelStatus Monitoring Monitor Microphone Type Monitor Microphone BatteryMonitor Microphone Version Using the Serial Control Processor RS-232 or IP Monitor DIP SwitchesUsing the Executive HD Base Station with a Control System Monitor VersionsSerial Command & Return Strings String TablePage Using the Executive HD Base Station with a DSP Channel #Examples ClearOne Converge & XAPBiamp Audia & Nexia MUTE4Polycom SoundStructure Using the Base Station Front Panel Display Using the HD Wearable Wireless Microphones Revolabs HD Microphones and HD Microphone AdaptersAdjusting the Volume on the Wearable Microphone Earpiece Pickup 360 ºPattern Acoustic Cover protects microphone element non-removable Using the HD XLR Microphone Wireless Adapter Using the HD Wireless Adapter for Countryman Microphone Pairing Wireless Microphones to Base Station Revolabs Executive HD Charger Base Power Module Updating the Revolabs Hdtm FirmwareCharging the Microphone Batteries Updating the Executive HD Base Station & MicrophonesPage Revolabs Executive HD Indicator LEDs GreenWarranty Specifications Dimensions, L, W, H and WeightMaximum Audio Channels Power Cord Receptacle LED indicatorIndex Charger Bays