SoundCraft 1601E manual Initial Wiring Considerations, Audio Wiring, Shielding

Page 10

INITIAL WIRING CONSIDERATIONS

For optimum performance, it is essential for the earthing system to be clean and noise free, as all signals are referenced to this earth. A central point should be decided on for the main earth point system, and all earths should be 'star fed' from this point. It is common electrical practice to `daisy chain' the earths to all electrical outlets but this method is unsuitable for audio installations. The preferred method is to run an individual earth wire from each outlet, back to the system star point to provide a safety earth screen reference for each piece of equipment. A separate earth wire should also be run from each equipment rack and area, to the star point. This may or may not be used depending on circumstances, but it is easier to install in the first place, than later when problems arise. The location of the star point should be a convenient, easily accessible place, preferably at the rear of the console or in the main equipment rack.

Install separate 'clean' and 'dirty' mains outlets, wired individually back to the incoming mains distribution box. Use the 'clean' supply for all audio equipment and the `dirty' supply for all lighting, etc. Never mix the two systems.

If necessary, to provide sufficient isolation from mains borne interference on the booth output, install an isolating transformer. This should be provided with a Faraday Shield which must be connected with earth.

Never locate the incoming mains distribution box near audio equipment, especially tape recorders, which are very sensitive to electromagnetic fields.

Ensure that all equipment racks are connected to earth, via a separate wire back to the star point.

Equipment which has unbalanced inputs and outputs may need to be isolated from the rack to prevent earth loops.

AUDIO WIRING

Having provided all equipment with power and earthing connections, consideration must be given to the method of providing audio interconnection and adequate screening of those interconnections. This must be done in a logical sequence to avoid problems and assist in the localisation of problem equipment.

Connect the Main or Booth system to the console and check for any hum, buzz, or RFI. Only when you are satisfied with the quietness of the console and the PA system should you proceed with the next step.

Connect decks or CD players, FX and sends one at a time, checking and isolating any connection which degrades performance.

Connect all other peripheral devices.

Connect all microphone lines.

By following this sequence much time and future trouble will be saved, and the result will be a quiet, stable system.

SHIELDING

Audio equipment is supplied with a variety of input and output configurations, which must be taken into consideration when deciding where the screen connections should be made. There are three sources of unwanted signal being impressed on the screen, which are as follows:

Extraneous electrostatic or electromagnetic fields.

Noise and interference on the earth line.

Capacitive coupling between the screen and signal wires.

To minimise the adverse affects of the unwanted coupling to the signal wires, it is important that the screen is connected at one end only, i.e. the screen must not carry any signal current. Any signal on the wires within the screen will be capacitively coupled to the screen. This current will ultimately be returned to the source of the signal, either directly, if the screen is connected at the signal source end, or indirectly via the earthing system, if the signal is connected at the signal destination end. The indirect connection will cause an increase in high frequency cross-talk, and should be avoided wherever possible.

Therefore, in general, always connect the shield only at the signal source end. In high RF areas, the screen can also be connected to earth via a 0.01 mF capacitor. This will present a short circuit at RF frequencies, thus lowering the effective shield impedance to ground. However, at low audio frequencies the capacitor will effectively be an open circuit and thus not cause an earth loop problem.

10

Image 10
Contents Page Potters BAR Contents Important Safety Instructions Green and Yellow US Green/Yellow TIP Safety Symbol GuideHeadphones Safety Warning Recommended Headphone Impedance = 200 OhmsIntroduction BPM EffectsPage General Precautions InstallationMains Installation Audio Wiring Initial Wiring ConsiderationsShielding Points to Remember Working Safely with SoundUnpacking and Inspection Inspection and InstallationPowering Environmental ConsiderationsConnecting to a Typical Sound System Changing The Orientation Of The Phono/Line Switches Making Adjustments and Fitting SparesSetting The Pre-trim Pads Replacing The FadersPage Description TOP PanelBPM FX Section see BPM FX MIX FaderBalanced Master Outputs -XLR Connectors Rear Connector PanelBalanced Booth Outputs -XLR Connectors Front Panel EQ CUT -RotaryGetting Started Combi -XLR ConnectorOperation MIC / Line InputEQ -HIGH Control Level ControlEQ -LOW Control MIC Insert Socket rearconClip Indicators Input Selector SwitchesPRE-TRIM Pads HI EQ Channel Volume FadersTrim MID EQRecord OUT FX Send & Return / AUXSend -LEVEL Send -SELECTFX SEND/RETURN RE-CONFIGURATION Clip IndicatorFX ON/OFF Switch Return / AUX -LEVELMaster / Booth Output Exciter FaderFader Curve MASTER/CUE Select Headphone MonitorLevel Headphone SocketsMonitor BPM FX Module Bank ModeBeats Indicator Operating CriteriaIsolator TAP/CLEARY Controls ON-OFF switches BPM FX MIXConnections Setting UPQuick Start Activating the EffectsTAP/CLEAR Button OperationBPM Range TAP -Tempo EditEffect Start Sync Applying the BPM-FXMIX Fader Effect ControlsRotary Encoder Band Isolator Mode Bank select SINGLE/MULTI Mode OperationSingle Mode Additional speed settings for FILTER/FLANGER/PANNER Multi ModeProgram Edit and Recall Filter EffectsFrequency SUB-MENU Speed DelayRepeats Y SPS PANWAY Split Y Depth X mark space ratio CutterSlope Y Resonance is factory set @ 75% FlangeDepth Y PRE-SET Voice List Hints & TipsBlock Diagram Connecting Leads Troubleshooting Specifications Warranty Glossary Post after the channel faderEqualising the system to notch out the offending frequencies Riaa