SoundCraft 1601E manual Important Safety Instructions

Page 4

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of a polarised or grounding type plug. A polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4

Image 4
Contents Page Potters BAR Contents Important Safety Instructions Green and Yellow US Green/Yellow Safety Symbol Guide Headphones Safety WarningTIP Recommended Headphone Impedance = 200 OhmsIntroduction BPM EffectsPage General Precautions InstallationMains Installation Audio Wiring Initial Wiring ConsiderationsShielding Points to Remember Working Safely with SoundInspection and Installation PoweringUnpacking and Inspection Environmental ConsiderationsConnecting to a Typical Sound System Making Adjustments and Fitting Spares Setting The Pre-trim PadsChanging The Orientation Of The Phono/Line Switches Replacing The FadersPage Description TOP PanelBPM FX Section see BPM FX MIX FaderBalanced Master Outputs -XLR Connectors Rear Connector PanelBalanced Booth Outputs -XLR Connectors Front Panel EQ CUT -RotaryCombi -XLR Connector OperationGetting Started MIC / Line InputLevel Control EQ -LOW ControlEQ -HIGH Control MIC Insert Socket rearconClip Indicators Input Selector SwitchesPRE-TRIM Pads Channel Volume Faders TrimHI EQ MID EQFX Send & Return / AUX Send -LEVELRecord OUT Send -SELECTClip Indicator FX ON/OFF SwitchFX SEND/RETURN RE-CONFIGURATION Return / AUX -LEVELMaster / Booth Output Exciter FaderFader Curve Headphone Monitor LevelMASTER/CUE Select Headphone SocketsMonitor Bank Mode Beats IndicatorBPM FX Module Operating CriteriaIsolator TAP/CLEARY Controls ON-OFF switches BPM FX MIXSetting UP Quick StartConnections Activating the EffectsOperation BPM RangeTAP/CLEAR Button TAP -Tempo EditEffect Start Sync Applying the BPM-FXMIX Fader Effect ControlsRotary Encoder Band Isolator Mode Bank select SINGLE/MULTI Mode OperationSingle Mode Additional speed settings for FILTER/FLANGER/PANNER Multi ModeProgram Edit and Recall Filter EffectsFrequency SUB-MENU Speed DelayRepeats Y SPS PANWAY Split Y Depth X mark space ratio CutterSlope Y Resonance is factory set @ 75% FlangeDepth Y PRE-SET Voice List Hints & TipsBlock Diagram Connecting Leads Troubleshooting Specifications Warranty Glossary Post after the channel faderEqualising the system to notch out the offending frequencies Riaa