SoundCraft 1601E manual BPM FX Section see, BPM FX MIX Fader

Page 17

1.MIC/LINE INPUT (see page 20): This section features [LEVEL], [EQ-HI] and [EQ-LOW] controls for the microphone/line level input stage. The combi-XLR connector accepts XLR connectors for microphone use and 1/4” Jack plugs for mono line level devices (CD/tape players, drum machines, synthesizers etc.) The [MIC] push-button switch selects the alternative rear panel RCA phono socket inputs when it is released (up). This pair is mono summed and fed to the mix bus directly, bypassing the X-fader..

2.CHANNEL 1 INPUT (see page 22): This section features [TRIM], [PHONO/LINE select], [EQ-LOW], [EQ-MID], [EQ-HI] and [FADER] controls for the channel 1 input stage. There is also a 20dB pad and a 10dB pad, which can be set via holes under the top panel fascia; these are intended to be set at installation. The [CLIP] indicator shows the pre-A-to-D convertor level status. The 10- way indicator shows channel level. This channel can be used with any CD/line or Phono level input device.

3.CHANNEL 2 INPUT (see page 22): This section is functionally identical to Channel 1.

4.FX SEND/RETURN -AUXILIARY INPUT (see page 24): This section features [SEND LEVEL], [SEND SELECT], [RETURN /AUX LEVEL] and [RETURN/AUX SELECT] controls for the effects loop/auxiliary input stage. The [CLIP] indicator shows the pre-A/D convertor level status for the effects return/auxiliary input. The RETURN/AUX channel can be used with any CD/line level input device, as an additional stereo input.

5.FX ON/OFF SWITCH (see page 25): This 3-way “paddle” switch controls the effect send/return loop.

6.X-FADER MONITOR (see page 29): This control allows you to monitor channel 1, channel 2 or a mix of both.

7.MASTER/BOOTH OUTPUT (see page 26): This section features the [MASTER LEVEL] and [BOOTH LEVEL] controls. The 10- way VU indicator shows the MASTER output level.

8.X-FADER(see page 27): Note the adjustments on the front panel (see page 19).

9.INPUT FADERS (see page 22): Note the Ch1 and Ch2 adjustments on the front panel (see page 19).

10.EXCITER (see page 27): Frequency and Mix controls.

11.PHONO/LINE INPUT SWITCH (see page 22): 2-position switches select between each channel’s phono and line switches.

12.PBM FX ASSIGN (see page 33): Assigns BPM FX to the input channel (post fader).

13.BPM FX SECTION (see page 30):

14 BPM FX MIX FADER

17

Image 17
Contents Page Potters BAR Contents Important Safety Instructions Green and Yellow US Green/Yellow Headphones Safety Warning Safety Symbol GuideTIP Recommended Headphone Impedance = 200 OhmsBPM Effects IntroductionPage Mains Installation InstallationGeneral Precautions Shielding Initial Wiring ConsiderationsAudio Wiring Working Safely with Sound Points to RememberPowering Inspection and InstallationUnpacking and Inspection Environmental ConsiderationsConnecting to a Typical Sound System Setting The Pre-trim Pads Making Adjustments and Fitting SparesChanging The Orientation Of The Phono/Line Switches Replacing The FadersPage TOP Panel DescriptionBPM FX MIX Fader BPM FX Section seeBalanced Booth Outputs -XLR Connectors Rear Connector PanelBalanced Master Outputs -XLR Connectors EQ CUT -Rotary Front PanelOperation Combi -XLR ConnectorGetting Started MIC / Line InputEQ -LOW Control Level ControlEQ -HIGH Control MIC Insert Socket rearconPRE-TRIM Pads Input Selector SwitchesClip Indicators Trim Channel Volume FadersHI EQ MID EQSend -LEVEL FX Send & Return / AUXRecord OUT Send -SELECTFX ON/OFF Switch Clip IndicatorFX SEND/RETURN RE-CONFIGURATION Return / AUX -LEVELMaster / Booth Output Fader Curve FaderExciter Level Headphone MonitorMASTER/CUE Select Headphone SocketsMonitor Beats Indicator Bank ModeBPM FX Module Operating CriteriaY Controls TAP/CLEARIsolator BPM FX MIX ON-OFF switchesQuick Start Setting UPConnections Activating the EffectsBPM Range OperationTAP/CLEAR Button TAP -Tempo EditApplying the BPM-FX Effect Start SyncRotary Encoder Effect ControlsMIX Fader Band Isolator Single Mode SINGLE/MULTI Mode OperationMode Bank select Program Edit and Recall Multi ModeAdditional speed settings for FILTER/FLANGER/PANNER Frequency EffectsFilter SUB-MENU Repeats Y DelaySpeed WAY Split Y PANSPS Slope Y CutterDepth X mark space ratio Depth Y FlangeResonance is factory set @ 75% Hints & Tips PRE-SET Voice ListBlock Diagram Connecting Leads Troubleshooting Specifications Warranty Post after the channel fader GlossaryEqualising the system to notch out the offending frequencies Riaa