Aviom A-16R, A-16CS manual Footswitch Jack

Page 62

Aviom A-16R and A-16CS User Guide

Footswitch Jack

The A-16CS can use any standard dual-pedal footswitch to select Presets in the A-16R. When using a dual pedal, the right-side pedal is used to move forward through the Preset list. The left pedal is used to move backward through the Preset list from the current selection.

For example, if you have just loaded Preset 7 (by pressing the RECALL button followed by the number 7 button), pressing the right pedal once will move to Preset 8. Pressing the left pedal will move down one, returning you to Preset 7. Another press of the left pedal loads Preset 6, and so on. Changes are reflected on the A-16CS and its connected A-16R host.

As with other operations involving the A-16CS, the REMOTE/LOCAL switch must be in the REMOTE position in order for the footswitch to be functional. When a Preset is selected via the footswitch, the corresponding numbered button’s LED on the front panel of the A-16R will flash to indicate that the Preset has been loaded.

The Footswitch jack uses a TRS connection, designed for dual foot pedals. However, you can substitute a single footswitch (one that has only a tip-sleeve connection) if necessary. The Presets will move up only, and will wrap around from Preset 16 to Preset 1 at the end of the Preset list as described previously.

The footswitch can be either a normally open or normally closed type. The pedal is scanned by the system software to determine which type it is, and to determine what the “up” state of the switch is. The foot pedal should be connected when the system is powered up. If you change pedals while the system is in use, you may need to power cycle the unit if the type of pedal is different.

Note: When selecting Presets with a footswitch, the selections will wrap around and start over after you reach the last numbered Preset.

For example, when moving forward through the Preset list from Preset 14, after two presses of the right footswitch you will be at Preset 16. One more press of the same footswitch will select Preset 1, the first Preset in the list. Additional presses of the right footswitch continue selecting Preset 2, Preset 3, etc.

52

Image 62

Contents 16R Personal Mixer 16CS Control Surface User GuideAviom, Inc Page Warranty Information Read this First Aviom, Inc. Limited Warranty Table of Contents Table of Contents Midi I/OMidi Page Features WelcomeConventions Used in this Document Optional Remote ControlUsing Personal Mixers Button PressesMaster Volume Control 16R Front Panel 16R Components left side16R Components right side 16R Rear Panel Audio Connections16R Midi and Data Connections 16CS Components Left Side16CS Right Side Package Contents AC Line ConditioningMixer Label Strip Installing the A-16R in a RackChannel Labels Category 6 Cables What is Category 5?Cables Used in the Aviom System Infinite number A-Net components Cable LengthsUp to 500 feet of Cat-5 cable can be used to connect About A-Net Power Supplies Power Supply PolarityCleaning Maintenance System Interconnections System SetupAC Power Connection Labeling the Channels Audio Connections InputsAudio Connections Outputs Preparing to Make a Mix Powering UpBasic Navigation Set the Pan Location Set the Channel VolumeMixing Saving Your New Preset What Gets SavedInformation Not Saved With a Preset Net Connection Options Parallel A-Net routing using an A-16D A-Net DistributorSystem Navigation Series ConnectionMixing 16D ProA-16R Personal Mixer Operational ModesGlobal Controls the Master Section Tone ControlsMaster Volume Button BehaviorsMaking Changes to Channel Settings Before You Start Editing Pan LEDs Volume and Pan ControlPan and Volume Controls Spread turns this Linking ChannelsSpread Control Single-Channel Solo Held Solo ModeSolo Modes Into this, for exampleMuting a Channel Creating Groups Creating Additional Groups Removing Channels From a Group Changing Channel Volumes Within a GroupMaking Changes to a Group Muting Groups Audio Outputs Net ConnectorsDC Power Input Stereo Operation Mono OperationBalanced Inserts Signal Flow MixControl Midi I/O Net In and OutAviom A-16R and A-16CS User Guide Global Controls OverviewA-16CS Front Panel Master Volume Button Behaviors All Volumes Zero Changing Channel SettingsChannel Volume and Pan Control Muting a Channel Recalling a Preset From the A-16CS Saving a Mix From the A-16CSDisplay the Current Preset Number A-16CS Rear PanelFootswitch Jack Midi Midi JacksMidi Out 16R Midi Base ChannelMidi Midi ThruMidi Automation Data Storage MidiSaving Presets Save One Mix Preset via MidiSaving All Mix Presets via Midi Loading One Preset via Midi Loading . via MidiLoading an All Preset File via Midi Exit Midi ModePage Problem Can’t change Presets TroubleshootingProblem No audio from the Personal Mixer outputs Problem Can’t hear a Channel that is part of a GroupProblem The A-Net LED is on, but there is no sound Problem Don’t know if a Preset was saved Problem In Group mode, can’t select a new Channel16CS Control Surface Specifications16R Personal Mixer Midi Implementation Chart Midi System Exclusive Implementation Version 1.00 for Aviom A-16RMidi System Exclusive Packet Head Message Data Format Midi All Presets Message Type = 00H Midi Current Preset Message Type = 01H Presetsmsg 1111 F7H End of Exclusive 0111 Valid preset Range Midi Current Preset Detail 1111 F7H End of Exclusive 0111 Symbols IndexIndex LAN Muting a Channel 33 Program Change Muting Groups XLR Aviom Warranty Registration