SP Studio Systems SP-12 manual 2K Adding Swing

Page 36

RECORDING SEGMENTS

2K ADDING SWING

While in segment mode, you may specify that a segment have a particular rhythmic swing to it. The SP-12 defaults to a “swing factor” of 50%, which means that each quarter note is weighted so that the first eighth note takes up 50% of the quarter note, and the second eighth note takes up the other 50%. This is the way you would normally expect things to be.

However, you may change the swing factor to 514%, 58%, 63%, 67%, or 71%. For example, with a swing factor of 58%, the first eighth note spreads out slightly to take up 58% of the quarter note, while the second eighth note shrinks slightly so that it takes up 142% of the quarter note. This lets you program a swinging, less metronomic feel to individual segments.

To program a segment for swing, you must be in segment mode. Then, follow these steps:

1.The SP-12 must be stopped (RUN/STOP light off). Press SWING.

2.The display shows the current swing setting for the selected segment. The Right Arrow and Left Arrow buttons step through the various swing options.

3.When the display shows the desired swing value, press ENTER.

Notes: Swing can help add a more human “feel” to a series of repeating segments. For example, if you repeat the same segment four times, try setting a swing factor of 514% for, say, the third segment. This results in a series of segments that are more psycho-acoustically interesting than merely repeating the same pattern over and over.

67% is considered the “classic” jazz swing factor, where the first eighth note is 2/3 of a quarter note, and the second eighth note is 1/3 of a quarter note (i.e. the second eighth note behaves more like an eighth note triplet). If this sounds too “perfect”, try a swing factor of 64% instead. The results will be similar, but the “feel” will be slightly different.

If you’re trying to record or erase in a segment that has a swing factor other than 50%, there are two cautions. To erase a specific note, you have to erase where the note would normally occur If the segment had a 50% swing factor. If you record while a segment is in swing mode, the beats may or may not fall where you want them to fall. Therefore, it’s best to go out of swing mode when recording or erasing, then re- enter swing mode after you’ve finished your alterations.

© E-mu Systems, Inc. 1985

Page 36

Enhanced by The Emulator Archive 2002

www.emulatorarchive.com

Page 35 Page 37
Image 36
Page 35 Page 37
Contents SP-12 Contents Part 3 Creating a Song Part 2 Recording SegmentsPart 5 Saving Your Data Part 6 MIDI, SYNC, & SmptePart 7 Mixing and Processing AppendixWhat is IT IntroductionIntroduction What is IT? Accessing Functions Within the Module What’s a Default?SP-12 Ground Rules Activating and De-activating ModulesSettings and Values EnteringLeading Zeroes Segment and Song ModesTransitory Nature of Segment Mode Beep MessagesRight Arrow/Left Arrow Buttons stepping and fast forwarding Current Song Display1A Setup Getting ReadyPart 1 Getting Ready 1A Setup 1B Instant Gratification 1C Background the Performance Module 1D Selecting Drum Sounds1E Adjusting the MIX 1F Tuning the DRUMS/CHANGING Decay SET-UP 1G Background Setting UP Additional Sounds1H ACCESSING/EXITING Multilevel SET-UP 12 1I ACCESSING/EXITING Multipitch SET-UP 11 Enter1J Accessing Dynamics SET-UP 1K Storing Defining a MIX SET-UP1L Auditioning Selecting a MIX SET-UP 1M Assigning Drum Sounds to Output Channels1N Playing Back Segments 1O Setting Tempo 1P Programming the Metronome Recording Segments Part 2 Recording Segments2A Recording a Segment Overview 2B Erasing a Segment Part 1 Standard Dimensioning Part 2 Real-Time Dimensioning 2D Understanding Auto Correct Recording Segments 2E Setting Auto Correct 2F Recording a Segment in Real TimeRecording Segments 2G Recording a Segment in Step Time 2H Erasing a Specific Drum Sound 2I Erasing a Specific Note of a Drum Track2J Copying and Appending Segments 2K Adding Swing 2L Swapping Drum Sounds 2M Copying Sounds2N Clearing the Memory 2M Check Remaining MemoryCreating a Song Part 3 Creating a Song3A Creating a Song Overview 3B Selecting a Song 3C Chaining Segments Together Segment #3D Ending a Song 3E Editing Songs STEPPING, INSERTING, Deleting 3F Using Repeats Song Step # 3G Changing the Song Drum Sound MIX 3H Setting Song Tempo 3I Programming Tempo Changes Within a Song Example3J Jumping to a SUB-SONG 3K Programming Trigger Outputs3L Starting AT a Specified Point in the Song 3M Efficient USE of Memory Sampling Your OWN Sounds Part 4 Sampling Your OWN Sounds4A Sampling AN Overview 4B Setting Levels Prior to Sampling 4D Setting the Sampling Threshold 4C Assigning the Sample4E Setting the Sample Length 4F Initiating and Stopping Sampling4G Deleting a User Sound 4H Modifying a Sample VIA Truncation and Loop Sampling Your OWN Sounds Mu Systems, Inc Enhanced by The Emulator Archive Saving Your Data Part 5 Saving Your Data5A Background Saving Data 5B General Care & Handling of Disks & CassettesLabeling Write-protecting disks and cassettesSaving Your Data 5C Hooking UP the 1541 Disk Drive or Cassette 5D Formatting Disks CASSETTE/DISK 5E Disk and Cassette Operations Load Sounds Disk Key in 2 then Cassette Key 1 thenVerify Sequences Disk Key in 2 then 7 Cassette Key 1 then MIDI, Sync & Smpte Part 6 MIDI, SYNC, & Smpte6A Midi Channel and Mode Select OverviewAfter selecting the desired mode, press Enter 6B Background Synchronization 6C Internal Sync Sync6D Midi Sync Sync 6E Smpte Sync Sync 6F Click Sync Sync 6G Writing Smpte Time Code on Tape 6H Writing a 24 Ppqn Click Sync Track on Tape Mixing and Processing Part 7 Mixing and Processing7A Mixing and Processing Overview 7B Pseudo Automated Mixdown7C Creating Ambience 7D Using Special Effects in the Studio Appendix AppendixAppendix a the ART of Sampling Part 1 Taking the Best Possible SampleGeneral Tips Dynamics Appendix Sampling from Tapes Part 2 Manipulating the Sample Mu Systems, Inc Enhanced by The Emulator Archive Appendix B Understanding Rhythmic Notation Appendix C Understanding Time Signatures Appendix D Understanding MIDI/SMPTE What does the Midi cable do?What does Midi stand for? How can information control a synthesizer or drum machine?How does Midi differentiate between different instruments? Channels, huh? Sounds like a lot of patch cords to meWhat kind of words does the Midi language include? Dealing With MlDlosyncracies SmpteAppendix E Tips on Creating Realistic Drum Parts Appendix F Tips on Using Cassette Interfaces Appendix Appendix G HOW the SP-12 Works Appendix H Special Functions SET-UP #23 Procedure Display Reads Press Appendix

SP-12 specifications

The SP Studio Systems SP-12 is a cutting-edge digital audio workstation that embodies innovation, versatility, and user-friendly design. Designed for both professional studios and home setups, the SP-12 sets a new standard in sound production and music creation. It combines advanced technology with an intuitive interface, making it suitable for both seasoned producers and beginners alike.

At the heart of the SP-12 is its powerful multi-core processor, allowing for seamless performance and efficient audio processing. This hardware design ensures that users can run multiple plug-ins and tracks without experiencing latency or lag, providing a smooth workflow that enhances creativity. Additionally, the SP-12 boasts a robust memory capacity, supporting extensive sample libraries and a vast array of sounds for diverse musical styles.

One of the standout features of the SP-12 is its advanced sampling technology. Users can import, edit, and manipulate samples with precision. The unit supports high-resolution audio formats, ensuring pristine sound quality. The intuitive software interface allows for easy navigation through samples, enabling users to chop, slice, and rearrange audio files effortlessly. This flexibility is a game-changer for producers looking to create unique tracks.

Another key characteristic is the SP-12's extensive connectivity options. It includes multiple USB ports, MIDI inputs and outputs, and analog connections, allowing for integration with various instruments and external devices. This versatility ensures that users can expand their studio setup according to their specific needs, whether they use it for live performance or studio recording.

Additionally, the SP-12 features an in-built sequencer that supports advanced MIDI functionalities, enabling users to create complex arrangements and orchestrate their musical ideas. Moreover, the workstation includes a comprehensive suite of virtual instruments and effects, allowing producers to shape their sound without needing third-party software.

Moreover, the SP-12's durable build quality and sleek design make it a stylish addition to any studio. Its compact form factor makes it portable, catering to musicians who need to produce music on the go.

In sum, the SP Studio Systems SP-12 is not just a digital audio workstation; it is a creative powerhouse. With its high-performance hardware, advanced sampling capabilities, extensive connectivity options, and user-friendly interface, it stands out as an essential tool for anyone serious about music production. Whether you’re composing, recording, or performing, the SP-12 is designed to inspire creativity and elevate your sound to new heights.
Top Page Image Contents