Desa (V)T36NA installation manual Installing Log No

Page 26

Fireplace

Installation

Continued

6.Place log #6 (left log) onto two pins on left side of back and front log. See Figure 48.

7.Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of lava rock provided.

NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner will cause performance problems.

8.Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto exposed section of front burner and along space between burner and grate prongs (see Figure 49). This will create glowing ember appearance as flame touches ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of ember material provided.

9.Close glass door, lock door latches, replace screen and close louvers (see Removing/Replac- ing Glass Door, steps 5 through 7, page 24).

WARNING: The glass door must be securely in place before running this fireplace. Do not run this fireplace if glass is missing or broken.

3

Figure 46 - Installing Log No. 3

4

1

Figure 47 - Installing Log No. 4

6

5

Figure 44 - Installing Log No. 1

2

Figure 48 - Installing Logs No. 5 and No. 6

 

Ember Material

 

Figure 49 - Placing Ember Material on

Figure 45 - Installing Log No. 2

Burner

26

www.desatech.com

111250-01E

Page 25 Page 27
Image 26
Page 25 Page 27
Contents What to do if YOU Smell GAS Table of Contents Safety InformationSafety Information Product Identification Product FeaturesLocal Codes High traffic areasThis fireplace does not require electricity to operate Pre-Installation PreparationLocation and space requirements Proper clearances must be maintainedFront Top of Standoffs Vent See venting ClearancesFraming and finishing Venting clearancesLocation of Termination Cap Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior Ground Floor Installation 32 minSnorkel Termination Installation Recommended Applications Corner ground floor installationHorizontal System Installation Using TWO 90 Elbows Connect a section of pipe and extend up through the hole Installation for vertical terminationFlat Ceiling Installation Twist-lock the vent cap onto the last section of vent pipe High Altitude Installation Vertical VentingDesa Terminations Desa Venting AccessoriesDesa Elbows Number DescriptionModel BK Installation Fireplace InstallationInstalling optional blower accessories Check GAS TypeModel BKT Installation Plug in blower power cord to duplex outletInstallation Items Needed Installing Gas Piping to Fireplace LocationBlower Wiring Diagram Connecting Fireplace to GAS Supply Checking GAS ConnectionsPressure Testing Fireplace Gas Connections Test Pressures Equal To or Less Than Psig 3.5 kPaOpen bottom louver and locate the switch Installing optional wall mount switch GWMS2Installing Remote Receiver Removing Louver Panels Cleaning Glass DoorRemoving/Replacing Glass Door Removing Glass DoorInstalling logs, lava rock and glowing embers Close top and bottom louversInstalling Log No Lighting Instructions For your safety Read before lightingOperating Fireplace To Turn OFF GAS To ApplianceOn/Off Series Models HRC100 and HRC101 Manual Lighting ProcedureOptional Hand-Held Remote OperationAuto Shutoff Feature Operating optional blower accessorySafety Features Operating optional GWMT1 Wall Mounted ThermostatInspecting Burners Cleaning MaintenancePilot Assembly Burner Flame PatternVenting system Pilot and burnersLogs Troubleshooting Observed Problem Possible Cause RemedyBurner orifice clogged Clean burner see Cleaning Is lit Mocouple to cool, causingProblem could be caused by Replace pilot assembly After pilot lights, keep gasOr shut off Service person Remote does not function When burner is litDirty or partially clogged 3. Clean burner see Cleaning Tery power is lowGas leak. See Warning Statement aboveTechnical Service Replacement PartsService Hints SpecificationsRolled Louver Trim kit Wall mounted on/off switch gwms2 Not ShownFace/Louver Panel kit Deflection hoodIllustrated Parts Breakdown Rear Refractory Brick Panel Left Refractory Brick PanelIllustrated Parts Breakdown 11102 111250-01E 111250-01E Limited Warranty DIRECT-VENT Fireplace Warranty InformationKeep this Warranty

(V)T36NA specifications

Desa (V)T36NA is an advanced piece of machinery designed primarily for heavy-duty applications in various industrial sectors. Known for its reliability and efficiency, this model has gained popularity among operators seeking high performance without compromising on durability.

One of the standout features of the Desa (V)T36NA is its powerful engine. It is equipped with a state-of-the-art internal combustion engine that provides robust torque and horsepower, enabling it to tackle demanding tasks with ease. This power is complemented by a highly efficient fuel system that minimizes consumption, making it both cost-effective and environmentally friendly.

The Desa (V)T36NA incorporates cutting-edge technologies that enhance its operational capabilities. Its intelligent control system allows for seamless adjustments to power settings based on task requirements. This feature not only improves performance but also extends the lifespan of the machinery by preventing overexertion. Additionally, the unit is integrated with advanced diagnostic tools that monitor performance metrics, enabling operators to identify issues before they escalate.

Another notable characteristic of the Desa (V)T36NA is its robust construction. Built from high-grade materials, this machinery is designed to withstand the rigors of tough industrial environments. The frame is reinforced to handle heavy loads and resist wear and tear, which significantly reduces maintenance costs over time.

In terms of ergonomics, the machinery is designed with user comfort in mind. The operator's cabin is spacious, providing ample room and visibility for enhanced maneuverability. The controls are intuitively laid out, ensuring that operators can make adjustments quickly and efficiently.

The Desa (V)T36NA also emphasizes safety, featuring advanced safety mechanisms such as automatic braking systems and secure cabin enclosures. These features protect both the operator and the surrounding personnel, making it a reliable choice for any workspace.

Overall, the Desa (V)T36NA represents a significant advancement in heavy machinery, combining power, efficiency, and safety in one robust package. Its innovative technologies and solid construction make it an excellent investment for industries seeking to enhance productivity while ensuring operator comfort and safety. Whether in construction, manufacturing, or other heavy-duty applications, the Desa (V)T36NA stands out as a trustworthy ally in achieving operational goals.
Top Page Image Contents