Desa VDCFTNA installation manual For Built-In Installation, Extension Cord

Page 15

INSTALLATION

Continued

Remote/

Blower

Bracket

Switch

Plate

Screw

Figure 18 - Installing Switch Plate to

Remote/Blower Bracket

For Built-In Installation

WARNING: A licensed elec- trician must connect the wiring harness to electrical supply following all local codes. Electri- cian must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of fireplace.

1.Install snap bushing from blower kit into one hole on rear of remote/blower bracket (see Figure 19). The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Accessory, page 14.

3.A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 20).

4.Plug power cord to outlet receptacle (not provided) as shown in Figure 19. Wind the extra power cord and tie with plastic wire strap (see Figure 19). Set power cord bundle between the remote/blower bracket and outer casing, away from the burner.

5.Test to make sure blower is working properly.

6.Reinstall upper louver beginning with bottom screws (see Figure 15, page 14) and close lower louver.

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole re- ceptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An undersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

	Fan Switch
	(Auto/Off/On)
		1 Auto
	Off	2
		3			Blue		Thermostat
			On					Switch
			On					(N.O.)
110/115			Red						Blue
V.A.C.			Red						Blower
	Black									Motor
	Black							Red
								Red
	White							White
	Green							Green

Figure 20 - Wiring Diagram For Blower

Accessory Built-In Installation

Blower Bracket	Wire Harness
Blower Bracket
Assembly
Screw

Power Cord

Switch

Outlet Receptacle (not included)

3 2 1

Switch

Plate

Plastic Wire Strap Wire Harness

Lower Louver Door

Clamp Connector (not included)

Remote/ Blower Bracket

Figure 19 - Installing Blower Bracket Assembly

113133-01C

www.desatech.com

15

Image 15

Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory Thermostat Models Vdcftna and Vdcftpa Remote-Ready ModelsVdcfrpa and Vdcfrna Table of Contents Safety Information Safety Information Local Codes Optional Remote Control AccessoriesProduct Features Product IdentificationHood Assembly Air for Combustion VentilationTools Required Phillips screwdriver AIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationFireplace pilot and burner must be at least 18 above floor InstallationInstallation Items Fireplace ClearancesIf you have not installed hood, follow instruc- tions on Built-In Fireplace InstallationRoute flexible gas line through access hole in hearth base Optional Mantel InstallationInstalling Optional Blower Accessory GA3450TA Check all gas connections for leaks. SeeRemoving Upper Louver Installing Blower Accessory Remove 4 screws from upper louver see . Save these screwsOpen lower louver door by swinging door down see Figure Extension Cord For Built-In InstallationExternal Regulator With Vent Pointing Down Connecting to GAS SupplyConnecting equipment shutoff valve to heater control Installation Items NeededChecking GAS Connections Equipment Shutoff Valve Pressure Testing Fireplace Gas ConnectionsReplace battery cover onto remote control unit Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit Remove battery cover on back of remote control unitRemove jumper wire from control valve see , Optional Wall Switch GWMS2 Remote-Ready Models OnlyLighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceThermostat Control Operation Manual Lighting ProcedureOperating Fireplace To Turn OFF GAS To ApplianceOperating Blower AUTO/OFF/ON Blower SwitchDepress control knob and light pilot with match Thermostat Series Model HRC200 Optional Hand-HeldRemote Operation On/Off Series Model HRC100Key Pad Lock Feature Optional GWMS2 Wall Mounted SwitchSafety Features Auto Shutoff FeatureBurner Flame Pattern Cleaning MaintenanceInspecting Burners Pilot Flame PatternCabinet Cleaning MaintenanceWiring Diagram LOG SetObserved Problem Possible Cause Remedy TroubleshootingTroubleshooting Initial operation Processes and log curing When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning VDCFTPA, Vdcfrpa SpecificationsFirebox Models VDC Illustrated Parts BreakdownParts List Illustrated Parts Breakdown Thermostat ModelsVdcftpa and Vdcftna Parts List Vdcfrna and Vdcfrpa REMOTE-READY ModelsKEY Accessories Equipment Shutoff Valve GA5010THERMOSTAT-CONTROLLED Blower KIT GA3450T Receiver and HAND-HELD Remote Control KIT HRC100 AccessoriesWALL-MOUNT ON/OFF Switch Receiver and HAND-HELD Thermostat Remote Control KIT HRC200Parts Under Warranty Replacement PartsService Hints Technical Service113133-01C Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth