Desa VDCFTNA installation manual Depress control knob and light pilot with match

Page 24

OPERATING FIREPLACE

Continued

5.Press in and turn control knob counter-

clockwise to the PILOT position.

Press in control knob for five (5) seconds (see Figure 40).

Note: You may be running this fireplace for the first time after hooking up to gas sup- ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

8.Slightly push in and turn control knob coun-

terclockwise to the ON position.

9.Set flame adjustment knob to any level between HI and LO.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Piezo

Flame

Control

Ignitor

Button

Adjustment

Knob

 

Knob

 

Figure 40 - Control Knob and Ignitor

Button Location (Shown as Supplied

- No Control Options)

Pilot

Ignitor

Burner

Electrode

 

Figure 41 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

Electrode

 

Figure 42 - Natural Gas Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1. Turn control knob clockwise to the OFF position.

2. If Using Optional Hand-Held Remote: Set selector switch in the OFF position to prevent draining battery.

Shutting Off Burners Only (pilot stays lit) You may shut off the burners and keep the pilot lit by doing one of the following:

1.Turn control knob clockwise to the PILOT position.

2.If Using Optional Hand-Held Remote: Use remote control manual OFF button.

WARNING: Make sure re- mote sensor selector switch is in the OFF position when you are away from home for long periods of time.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, starting on page 23.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 8 and 9 under Lighting Instructions.

24

www.desatech.com

113133-01C

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory Thermostat Models Vdcftna and Vdcftpa Remote-Ready ModelsVdcfrpa and Vdcfrna Table of Contents Safety Information Safety Information Optional Remote Control Accessories Product FeaturesProduct Identification Local CodesHood Assembly Air for Combustion VentilationTools Required Phillips screwdriver AIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeInstallation Installation ItemsFireplace Clearances Fireplace pilot and burner must be at least 18 above floorBuilt-In Fireplace Installation If you have not installed hood, follow instruc- tions onOptional Mantel Installation Route flexible gas line through access hole in hearth baseInstalling Optional Blower Accessory GA3450TA Check all gas connections for leaks. SeeRemoving Upper Louver Installing Blower Accessory Remove 4 screws from upper louver see . Save these screwsOpen lower louver door by swinging door down see Figure For Built-In Installation Extension CordConnecting to GAS Supply External Regulator With Vent Pointing DownConnecting equipment shutoff valve to heater control Installation Items NeededChecking GAS Connections Pressure Testing Fireplace Gas Connections Equipment Shutoff ValveInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitRemove battery cover on back of remote control unit Replace battery cover onto remote control unitOptional Wall Switch GWMS2 Remote-Ready Models Only Remove jumper wire from control valve see ,Installing LOG SET and Screen For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsManual Lighting Procedure Operating FireplaceTo Turn OFF GAS To Appliance Thermostat Control OperationAUTO/OFF/ON Blower Switch Operating BlowerDepress control knob and light pilot with match Optional Hand-Held Remote OperationOn/Off Series Model HRC100 Thermostat Series Model HRC200Optional GWMS2 Wall Mounted Switch Safety FeaturesAuto Shutoff Feature Key Pad Lock FeatureCleaning Maintenance Inspecting BurnersPilot Flame Pattern Burner Flame PatternCleaning Maintenance Wiring DiagramLOG Set CabinetTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting When heated, vapors from Mote-Ready Models Only Power is lowSlight smoke or odor during Initial operation Processes and log curingGas leak. See Warning Specifications VDCFTPA, VdcfrpaIllustrated Parts Breakdown Firebox Models VDCParts List Illustrated Parts Breakdown Thermostat ModelsVdcftpa and Vdcftna Parts List REMOTE-READY Models Vdcfrna and VdcfrpaKEY Accessories Equipment Shutoff Valve GA5010THERMOSTAT-CONTROLLED Blower KIT GA3450T Accessories WALL-MOUNT ON/OFF SwitchReceiver and HAND-HELD Thermostat Remote Control KIT HRC200 Receiver and HAND-HELD Remote Control KIT HRC100Replacement Parts Service HintsTechnical Service Parts Under Warranty113133-01C Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth
Top Page Image Contents