Brinkmann 8300 owner manual Lighting Instructions, Match Lighting the Main Burners

Page 11

WARNING

Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual.

WARNING

LIGHTING INSTRUCTIONS:

Follow the instructions exactly.

1.OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down.

2.Check that all burner control knobs and the cylinder valve are turned to the "OFF" position.

3.Turn on the fuel supply by rotating the cylinder valve knob counter-clockwise to full open.

4.DO NOT stand with head, body, or arms over the grill when lighting.

LIGHTING THE MAIN BURNERS:

1. Open lid before lighting burner.

2. Make sure all control knobs are in the "OFF" position.

Note: The CENTER BURNER must be lit first, then light the left and right burners.

3. Push and turn the control knob for the CENTER BURNER to the "HIGH" position.

4. Press the electronic igniter and hold for 3–5 seconds to light burner.

5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF", wait 5 minutes to allow gas to dissipate and repeat lighting procedure.

6.If the CENTER BURNER does not ignite using the push-button igniter, wait 5 minutes, see "Match Lighting the Main Burners" section.

7.To light the left and right burners, push and turn control knobs to HIGH. Follow Step 5.

8.To turn off, turn each control knob clockwise until it locks in the "OFF" position. This does not turn off the gas flow from the cylinder.

Note: If burner does not light or flame is too low, you may have spider or other insect blockage in burner, or the flow limiting device has been activated. See "Burner Assembly/Maintenance" under Proper Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP Cylinder and Hose/Regulator to Grill.

MATCH LIGHTING THE MAIN BURNERS:

1.Open lid before lighting.

2.Turn the burner control knobs to OFF.

3.Place a paper match in the end of the matchlighter. Strike the match and place through lighting hole in the left hand side of the grill to approximately 1/2" (1 to 2 cm) from the burner.

4.Turn on the FAR LEFT burner control knob to the HIGH position. The burner should light within 5 seconds.

5.If the burner does not light, turn the control knob to OFF and wait 5 minutes for gas to evacuate the grill. Repeat Steps 1 through 5 until the burner ignites.

Lighting Hole

Matchlighter

6.Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the HIGH position.

7.If the burner does not light within the first few attempts of match lighting, there is a problem with the gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the problem is found and corrected. See “Trouble Shooting” section of this manual.

10

Image 11
Contents Avis À L’INSTALLATEUR Important Safety Table of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Hose and Regulator Installing the LP GAS Cylinder Onto the GrillRegulator Resetting Procedure Filling the LP GAS CylinderConnecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderChecking for Leaks Leak TestingWhen to Perform a Leak Test PRE-START Check List Match Lighting the Main Burners Lighting InstructionsLighting the Main Burners Turning OFF the Grill Lighting the Side BurnerMatch Lighting the Side Burner Controlling FLARE-UPS Operating the GrillBreaking in Your Grill Preheating the GrillSide Burner Rotisserie CookingHelpful Hints CleanlinessGrilling to Proper Temperature Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceTransporting and Storage Cooking GrillsHeat Distribution Plates Before Storing Your Grill Trouble ShootingFrequently Asked Questions Frequently Asked Questions Parts BAG Contents Parts List Assembly Instructions1519 Step Snap wheel hubcaps onto the outside of wheels as illustrated Grill Body Assembly Step Attach hose heat shield using two #8 self-tapping screws Step Place the side burner grate onto the side burner table Step Portland 8300 Assembled Importantes Relatives À LA Sécurité Mises EN GardeTable DES Matières Mises EN Garde Mises EN Garde GénéralesBouteille DE GPL NON Fournie Avec CE Gril Renseignements SUR L’INSTALLATIONSpécifications DE LA Bouteille Procédure DE Réenclenchement DU Régulateur Installation DE LA Bouteille DE GPL SUR LE GrilRemplissage DE LA Bouteille DE GPL Tuyau ET RégulateurRaccordement DE L’ENSEMBLE Tuyau / Détendeur Quand Effectuer UNE Épreuve D’ÉTANCHÉITÉ Épreuves D’ÉTANCHÉITÉListe DE Contrôle Avant L’ALLUMAGE Allumage DES Brûleurs Principaux À L’AIDE D’UNE Allumette Consignes D’ALLUMAGEAllumage DES Brûleurs Principaux Fermeture DU Gril Allumage DU Brûleur LatéralAllumage DU Brûleur Latéral À L’AIDE D’UNE Allumette Contrôle DES Embrasements Utilisation DU GrilMise EN Marche DE Votre Gril Préchauffage DU GrilBrûleur Latéral Cuisson AU TournebrocheConseils Utiles PropretéGrillage À LA Bonne Température Assemblage ET Entretien DES Brûleurs Nettoyage ET EntretienTransport ET Entreposage Assemblage DU Brûleur / Entretien SuiteGrilles DE Cuisson Plaques DE Diffusion ThermiqueDépannage Avant Dentreposer Votre GrilQuestions Posées Fréquemment Questions Posées Fréquemment Liste DES Pièces Instructions D’ASSEMBLAGEPage Contenu DU SAC DE Pièces Étape Étape LAssemblage du Corps du Grill Étape Étape Avertissement Contenant à Graisse Plateau à Graisse Étape Portland 8300 Assemblé Warranty