Maxon Telecom WL7-VERS. C-1K Mounting the Lift, Base Plate Bolt Hole Pattern

Page 28

MOUNTING THE LIFT

NOTE: MAXON recommends using all 10 carriage screws (Kit items) to bolt Lift to vehicle. A minimum of 8 screws or bolts and use of holes 1, 2, 3, 4 & 9 are required for correct installation. Also, the 3 front holes should be selected to give a symmetrical bolt pattern (i.e. holes 5,10, & 8 or holes 6,10, & 7).

11921

1.Use template (FIG. 27-1)or the base plate on the Lift (FIG. 28-1, holes 1-10)to mark eight (8) to ten (10) 7/16” mounting holes through the vehicle floor. Before drilling holes in the vehicle floor, make sure no wires and fluid lines are too close to hole locations. Drill holes 1, 2, 9, 3, and 4.

 

 

BACK

 

4

1

2

9

3

5

6

10

7

8

FRONT

Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

BASE PLATE BOLT

HOLE PATTERN

FIG. 28-1

NOTE: Vehicle floor must meet the requirements shown at the beginning of the VEHICLE REQUIREMENTS section in this Installation Manual.

2.Position Lift so holes 1-10in the base plate (FIG. 28-1)are aligned with the correct holes drilled in vehicle floor.

3. Temporarily secure Lift to vehicle with two mounting bolts (Kit items), inserted through base plate holes 1 and 4, or holes 2 and 3 (FIG. 28-1). Use two lock nuts and correct under-vehicle supports (Kit items) to secure the Lift. Use instructions supplied with vehicle installation kit to select the correct bolts, nuts and sup- ports. Alternately, tighten the two bolts and nuts to 20 to 30 LBS.-FT.

PATENTS PENDING

28

Image 28
Contents For Patents Pending For Inside Vehicle Installation onlyREV. a Patents Pending This page Intentionally Left Blank Table of Contents System Diagrams Completed Lift Installation ChecklistSafety Summary IntroductionSlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Vehicle Requirements Body StrengthForce & Moment Produced by Lift on Vehicle Floor FIG Lift Footprint on Vehicle Floor Lift with 33 or 34 PlatformSafety Interlock System Electrical PowerLighting Wheelchair Door Dimensions Vehicle RequirementsLift Dimensions Side View of Stowed Lift Front View of Stowed LiftWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components & Terminology Lift Components see TableName Description Threshold PlateDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller ANTI-SLIP & Safety Striping Wide PlatformANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Lift Installation Installation KitsPreparing and Positioning the Lift Vehicle RH Side ViewPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Mounting the Lift Base Plate Bolt Hole PatternInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Ground Cable Routed from Lift Bolting Ground Cable To Vehicle FrameConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Connecting Power to Lift Typical Hand PendantLift AT Floor Level Platform Lowered to Ground LevelHydraulic Fluid Level LH Pump Shown Checking Hydraulic Fluid LevelUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank Adjustments MAT Switch Adjustment if RequiredAdjusting Switch LH Side of Lift MAT Switch Adjustment ScrewsPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Using Backup Pump to Unfold Lift with LH Pump Inboard Switch Adjustment if RequiredPlatform AT Floor Level LH Side Shown Platform below Floor LEVEL, with Ibrs UP LH Side Shown Hand Pendant Entering Setup Turning Power Switch ON/OFF LH Pump ShownController Entering Setup Changing Controller to Spanish or English if RequiredHand Pendant Changing Setup Mode Controller Language Setting English or SpanishHand Pendant Changing the Setting Controller Exiting SetupOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop Overlaps Edge of Base Plate Inboard Rollstop with GAP Between Base PlateFloor Position Adjustment Controller Setting Floor Position Example Reading Shown FIGHand Pendant Changing the Setting Inboard Threshold Rollstop Plate System Diagrams Hydraulic System DiagramElectrical System Diagram Completed Lift Installation Checklist Check Lift OperationVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date