Maxon Telecom WL7-VERS. C-1K Slauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888

Page 7

1.Read and understand the instructions in this Installation Manual before installing Lift.

2.Before operating the Lift, read and understand the operating instructions contained in the Operator’s Manual.

3.Comply with all WARNING and instruction decals attached to both the Lift and the ve- hicle.

4.Keep decals clean and legible. If decals are illegible or missing, free replacement de- cals are available from MAXON Lift Corp. Customer Service. Refer to DECALS & DE- CAL PLACEMENT and the instructions for installing decals on vehicle in this manual.

5.Consider the safety and location of bystanders and location of nearby objects when op- erating the Lift. Stand to one side of platform while operating the Lift.

6.Do not allow untrained persons to operate the Lift.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

7	PATENTS PENDING

Image 7

Contents For Patents Pending For Inside Vehicle Installation onlyREV. a Patents Pending This page Intentionally Left Blank Table of Contents Completed Lift Installation Checklist System DiagramsIntroduction Safety SummarySlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Lift Footprint on Vehicle Floor Lift with 33 or 34 Platform Vehicle RequirementsBody Strength Force & Moment Produced by Lift on Vehicle Floor FIGSafety Interlock System Electrical PowerLighting Vehicle Requirements Wheelchair Door DimensionsSide View of Stowed Lift Front View of Stowed Lift Lift DimensionsWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components see Table Lift Components & TerminologyThreshold Plate Name DescriptionDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller Wide Platform ANTI-SLIP & Safety StripingANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Vehicle RH Side View Lift InstallationInstallation Kits Preparing and Positioning the LiftPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Base Plate Bolt Hole Pattern Mounting the LiftInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Bolting Ground Cable To Vehicle Frame Ground Cable Routed from LiftConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Hand Pendant Connecting Power to Lift TypicalPlatform Lowered to Ground Level Lift AT Floor LevelHydraulic Fluid Level LH Pump Shown Checking Hydraulic Fluid LevelUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank MAT Switch Adjustment if Required AdjustmentsMAT Switch Adjustment Screws Adjusting Switch LH Side of LiftPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Using Backup Pump to Unfold Lift with LH Pump Inboard Switch Adjustment if RequiredPlatform AT Floor Level LH Side Shown Platform below Floor LEVEL, with Ibrs UP LH Side Shown Changing Controller to Spanish or English if Required Hand Pendant Entering SetupTurning Power Switch ON/OFF LH Pump Shown Controller Entering SetupController Exiting Setup Hand Pendant Changing Setup ModeController Language Setting English or Spanish Hand Pendant Changing the SettingOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop with GAP Between Base Plate Inboard Rollstop Overlaps Edge of Base PlateController Setting Floor Position Example Reading Shown FIG Floor Position AdjustmentHand Pendant Changing the Setting Inboard Threshold Rollstop Plate Hydraulic System Diagram System DiagramsElectrical System Diagram Check Lift Operation Completed Lift Installation ChecklistVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date