Maxon Telecom WL7-VERS. C-1K Connecting Hand Pendant Cable RH Side Connection Shown

Page 34

ROUTE/CONNECT CABLES & HAND PENDANT - Continued

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

!CAUTION

To prevent vehicle access door from pinching and damaging the hand pendant cable, secure cable away from the door frame. Also, be sure that the hand pendant cable does not interfere with or bind against moving parts.

10.Connect the hand pendant cable as follows. Feed the cable through the hole located

in the main frame (FIG. 34-1). Secure cable strain relief to main frame with plastic nut (FIG. 34-1). Next, connect hand pendant connector to wiring harness (FIG. 34-1).

WIRING

HARNESS

CONNECTOR

MAIN

FRAME

HEX NUT

CONNECTOR	HAND

STRAINPENDANT

RELIEF

CONNECTING HAND PENDANT CABLE

(RH SIDE CONNECTION SHOWN)

FIG. 34-1

PATENTS PENDING

34

Image 34

Contents For Patents Pending For Inside Vehicle Installation onlyREV. a Patents Pending This page Intentionally Left Blank Table of Contents System Diagrams Completed Lift Installation ChecklistSafety Summary IntroductionSlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Force & Moment Produced by Lift on Vehicle Floor FIG Vehicle RequirementsBody Strength Lift Footprint on Vehicle Floor Lift with 33 or 34 PlatformSafety Interlock System Electrical PowerLighting Wheelchair Door Dimensions Vehicle RequirementsLift Dimensions Side View of Stowed Lift Front View of Stowed LiftWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components & Terminology Lift Components see TableName Description Threshold PlateDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller ANTI-SLIP & Safety Striping Wide PlatformANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Preparing and Positioning the Lift Lift InstallationInstallation Kits Vehicle RH Side ViewPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Mounting the Lift Base Plate Bolt Hole PatternInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Ground Cable Routed from Lift Bolting Ground Cable To Vehicle FrameConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Connecting Power to Lift Typical Hand PendantLift AT Floor Level Platform Lowered to Ground LevelHydraulic Fluid Level LH Pump Shown Checking Hydraulic Fluid LevelUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank Adjustments MAT Switch Adjustment if RequiredAdjusting Switch LH Side of Lift MAT Switch Adjustment ScrewsPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Using Backup Pump to Unfold Lift with LH Pump Inboard Switch Adjustment if RequiredPlatform AT Floor Level LH Side Shown Platform below Floor LEVEL, with Ibrs UP LH Side Shown Controller Entering Setup Hand Pendant Entering SetupTurning Power Switch ON/OFF LH Pump Shown Changing Controller to Spanish or English if RequiredHand Pendant Changing the Setting Hand Pendant Changing Setup ModeController Language Setting English or Spanish Controller Exiting SetupOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop Overlaps Edge of Base Plate Inboard Rollstop with GAP Between Base PlateFloor Position Adjustment Controller Setting Floor Position Example Reading Shown FIGHand Pendant Changing the Setting Inboard Threshold Rollstop Plate System Diagrams Hydraulic System DiagramElectrical System Diagram Completed Lift Installation Checklist Check Lift OperationVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date