Maxon Telecom WL7-VERS. C-1K Changing Controller to Spanish or English if Required

Page 48

CHANGING CONTROLLER TO SPANISH OR ENGLISH (IF REQUIRED)

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

NOTE: The power switch on the Lift must be turned OFF before entering SETUP.

1.Turn power switch OFF (FIG. 48-2).

2.Enter SETUP by holding both the UP and FOLD switches on the hand pendant (FIG. 48-1)and turning the power switch ON at the same time (FIG. 48-2). Controller will read SETUP (FIG. 48-3).

UP FOLD

HAND PENDANT:

ENTERING SETUP

FIG. 48-1

POWER

SWITCH

CONTROLLER

(REF)

TURNING POWER SWITCH ON/OFF

(LH PUMP SHOWN)

FIG. 48-2

SETUP

CONTROLLER:

ENTERING SETUP

FIG. 48-3

PATENTS PENDING

48

Image 48
Contents Patents Pending For Inside Vehicle Installation only ForREV. a Patents Pending This page Intentionally Left Blank Table of Contents System Diagrams Completed Lift Installation ChecklistSafety Summary IntroductionSlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Vehicle Requirements Body StrengthForce & Moment Produced by Lift on Vehicle Floor FIG Lift Footprint on Vehicle Floor Lift with 33 or 34 PlatformElectrical Power Safety Interlock SystemLighting Wheelchair Door Dimensions Vehicle RequirementsLift Dimensions Side View of Stowed Lift Front View of Stowed LiftWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components & Terminology Lift Components see TableName Description Threshold PlateDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller ANTI-SLIP & Safety Striping Wide PlatformANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Lift Installation Installation KitsPreparing and Positioning the Lift Vehicle RH Side ViewPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Mounting the Lift Base Plate Bolt Hole PatternInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Ground Cable Routed from Lift Bolting Ground Cable To Vehicle FrameConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Connecting Power to Lift Typical Hand PendantLift AT Floor Level Platform Lowered to Ground LevelChecking Hydraulic Fluid Level Hydraulic Fluid Level LH Pump ShownUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank Adjustments MAT Switch Adjustment if RequiredAdjusting Switch LH Side of Lift MAT Switch Adjustment ScrewsPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Inboard Switch Adjustment if Required Using Backup Pump to Unfold Lift with LH PumpPlatform AT Floor Level LH Side Shown Platform below Floor LEVEL, with Ibrs UP LH Side Shown Hand Pendant Entering Setup Turning Power Switch ON/OFF LH Pump ShownController Entering Setup Changing Controller to Spanish or English if RequiredHand Pendant Changing Setup Mode Controller Language Setting English or SpanishHand Pendant Changing the Setting Controller Exiting SetupOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop Overlaps Edge of Base Plate Inboard Rollstop with GAP Between Base PlateFloor Position Adjustment Controller Setting Floor Position Example Reading Shown FIGHand Pendant Changing the Setting Inboard Threshold Rollstop Plate System Diagrams Hydraulic System DiagramElectrical System Diagram Completed Lift Installation Checklist Check Lift OperationVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date