Maxon Telecom WL7-VERS. C-1K Inboard Rollstop Overlaps Edge of Base Plate

Page 53

3.If the inboard rollstop does not line up correctly with the edge of the base plate (FIGS. 53-1 and 53-2), go to IN-

STRUCTION 4.

THRESHOLD	EDGE OF
PLATE	INBOARD
	ROLLSTOP
EDGE OF
BASE PLATE

(888) 771-7713

NOTE: The power switch on the Lift must be turned OFF before entering SETUP.

4.Turn power switch OFF (FIG. 53-3).

INBOARD ROLLSTOP OVERLAPS

EDGE OF BASE PLATE

FIG. 53-1

THRESHOLD	EDGE OF
PLATE	INBOARD
	ROLLSTOP
EDGE OF
BASE PLATE

INBOARD ROLLSTOP WITH GAP

BETWEEN BASE PLATE

FIG. 53-2

POWER

SWITCH

CONTROLLER

(REF)

TURNING POWER SWITCH ON/OFF

(LH PUMP SHOWN)

FIG. 53-3

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX

53	PATENTS PENDING

Image 53

Contents REV. a Patents Pending For Inside Vehicle Installation onlyFor Patents Pending This page Intentionally Left Blank Table of Contents Completed Lift Installation Checklist System DiagramsIntroduction Safety SummarySlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Body Strength Vehicle RequirementsForce & Moment Produced by Lift on Vehicle Floor FIG Lift Footprint on Vehicle Floor Lift with 33 or 34 PlatformLighting Electrical PowerSafety Interlock System Vehicle Requirements Wheelchair Door DimensionsSide View of Stowed Lift Front View of Stowed Lift Lift DimensionsWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components see Table Lift Components & TerminologyThreshold Plate Name DescriptionDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller Wide Platform ANTI-SLIP & Safety StripingANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Installation Kits Lift InstallationPreparing and Positioning the Lift Vehicle RH Side ViewPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Base Plate Bolt Hole Pattern Mounting the LiftInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Bolting Ground Cable To Vehicle Frame Ground Cable Routed from LiftConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Hand Pendant Connecting Power to Lift TypicalPlatform Lowered to Ground Level Lift AT Floor LevelUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid LevelHydraulic Fluid Level LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank MAT Switch Adjustment if Required AdjustmentsMAT Switch Adjustment Screws Adjusting Switch LH Side of LiftPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Platform AT Floor Level LH Side Shown Inboard Switch Adjustment if RequiredUsing Backup Pump to Unfold Lift with LH Pump Platform below Floor LEVEL, with Ibrs UP LH Side Shown Turning Power Switch ON/OFF LH Pump Shown Hand Pendant Entering SetupController Entering Setup Changing Controller to Spanish or English if RequiredController Language Setting English or Spanish Hand Pendant Changing Setup ModeHand Pendant Changing the Setting Controller Exiting SetupOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop with GAP Between Base Plate Inboard Rollstop Overlaps Edge of Base PlateController Setting Floor Position Example Reading Shown FIG Floor Position AdjustmentHand Pendant Changing the Setting Inboard Threshold Rollstop Plate Hydraulic System Diagram System DiagramsElectrical System Diagram Check Lift Operation Completed Lift Installation ChecklistVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date