Maxon Telecom WL7-VERS. C-1K installation instructions Install Main Circuit Breaker

Page 30

INSTALL MAIN CIRCUIT BREAKER - Continued

2.Connect one end of power cable to 90 amp main circuit breaker (FIG. 30-1).

Do not connect battery end until instructed to connect the battery.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX

POWER UNIT

(REF)

1/4” FLAT

WASHER

(2 PLACES)

BATTERY

1/4”-20

LOCK NUT

(2 PLACES)

2 AWG POWER

CABLE (SHORT CABLE)

90 AMP MAIN CIRCUIT BREAKER

1/4”-20

CAP SCREW

(2 PLACES)

#12 SELF-DRILLING SCREW (4 PLACES)

2 AWG POWER CABLE (LONG CABLE CONNECTED BETWEEN TERMINAL OF STARTER SOLENOID AND MAIN CIRCUIT BREAKER)

MAIN CIRCUIT BREAKER & CABLING

FIG. 30-1

(888) 771-7713

3.Lastly, connect one end of long power cable to 90 amp main circuit breaker (FIG. 30-1).

PATENTS PENDING

30

Image 30

Contents Patents Pending For Inside Vehicle Installation only ForREV. a Patents Pending This page Intentionally Left Blank Table of Contents System Diagrams Completed Lift Installation ChecklistSafety Summary IntroductionSlauson Ave. Santa Fe Springs, CA 800 227-4116 FAX 888 Force & Moment Produced by Lift on Vehicle Floor FIG Vehicle RequirementsBody Strength Lift Footprint on Vehicle Floor Lift with 33 or 34 PlatformElectrical Power Safety Interlock SystemLighting Wheelchair Door Dimensions Vehicle RequirementsLift Dimensions Side View of Stowed Lift Front View of Stowed LiftWheelchair Door Body Clearance Points 32, 40, 42, 46 & 48 Floor Heights Lift Components & Terminology Lift Components see TableName Description Threshold PlateDecals and Decal Placement Decals for WL7-vers. C Decals and Decal Placement Serial Plate & Controller ANTI-SLIP & Safety Striping Wide PlatformANTI-SLIP & Safety Striping ANTI-SLIP & Safety Striping Preparing and Positioning the Lift Lift InstallationInstallation Kits Vehicle RH Side ViewPreparing and Positioning the Lift Using Template to Position Lift Using Template to Position Lift Vehicle Body Cutaway Base Plate Template Hole Pattern Mounting the Lift Base Plate Bolt Hole PatternInstall Main Circuit Breaker Install Main Circuit Breaker ROUTE/CONNECT Cables & Hand Pendant ROUTE/CONNECT Cables & Hand Pendant Ground Cable Routed from Lift Bolting Ground Cable To Vehicle FrameConnecting Hand Pendant Cable RH Side Connection Shown Typical Location Inside Vehicle For Stowing Hand Pendant Decals and Hand Pendant Mounting on Vehicle Connecting Power to Lift Typical Hand PendantLift AT Floor Level Platform Lowered to Ground LevelChecking Hydraulic Fluid Level Hydraulic Fluid Level LH Pump ShownUNBOLTING/BOLTING Pump Cover LH Pump Shown Checking Hydraulic Fluid Level This page Intentionally Left Blank Adjustments MAT Switch Adjustment if RequiredAdjusting Switch LH Side of Lift MAT Switch Adjustment ScrewsPlatform Tilt Adjustment Mandatory Platform Tilt Adjustment Screws Inboard Switch Adjustment if Required Using Backup Pump to Unfold Lift with LH PumpPlatform AT Floor Level LH Side Shown Platform below Floor LEVEL, with Ibrs UP LH Side Shown Controller Entering Setup Hand Pendant Entering SetupTurning Power Switch ON/OFF LH Pump Shown Changing Controller to Spanish or English if RequiredHand Pendant Changing the Setting Hand Pendant Changing Setup ModeController Language Setting English or Spanish Controller Exiting SetupOutboard Rollstop Time Adjustment if Required Controller Setting Outboard Ramp Time Range is -7 to 10 FIG Floor Position Adjustment Mandatory Inboard Rollstop Overlaps Edge of Base Plate Inboard Rollstop with GAP Between Base PlateFloor Position Adjustment Controller Setting Floor Position Example Reading Shown FIGHand Pendant Changing the Setting Inboard Threshold Rollstop Plate System Diagrams Hydraulic System DiagramElectrical System Diagram Completed Lift Installation Checklist Check Lift OperationVehicle I.D. VIN# Wheelchair Lift SERIAL# Checked by & Date