Invacare P9000 Adjusting Seat Depth Figure, Adjusting Back HEIGHT/ Replacing Back Canes Figure

Page 11

SEAT FRAME

PROCEDURE 4

This Procedure Includes the Following:

Adjusting Seat Depth

Adjusting Back Height /Replacing Back Canes

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.

ADJUSTING SEAT DEPTH (FIGURE 1)

1.Removetheexistingseatupholsteryfromthewheelchair. RefertoREPLACING SEAT UPHOLSTERYinPRO- CEDURE5oftheOwnersManual,partnumber1080737.

NOTE: If adjusting seat depth of the wheelchair, the seat upholstery MUST be changed as well.

2.Remove the two (2) plug buttons from the ends of the crossbraces that are towards front of wheelchair.

ADJUSTING BACK HEIGHT/ REPLACING BACK CANES (FIGURE 2)

1.

Remove the four (4) hex screws, washers and

 

locknuts that secure the two (2) back canes to the

 

wheelchair frame.

 

 

 

 

 

2.

Reposition the back canes to one (1) of five (5) pairs

 

of height adjustment holes:

 

 

 

 

 

 

 

 

 

ORIGINAL BACK

HEIGHT (IN INCHES)

 

 

 

 

 

 

 

 

 

✪ HOLE PAIR #

1

2

3

4

5

 

16-20-inches

16

17

18

19

20

 

 

 

 

 

 

 

✪ Holes numbered from bottom to top for reference only. (There are no numbers on the back canes.)

3. Reinstall the four (4) hex screws, washers and locknuts that secure the back canes to the wheelchair frame.

4. Securely tighten the hex screws and locknuts.

HOLE PAIR

S E A T

F

R A M E

NOTE: The two (2) plug buttons will be used in the ends of the seat extensions.

#

Back Cane

3.Install the two (2) seat extension tubes into the ends on the crossbraces. Line up the second mounting hole from the rear of the seat extension tube with the front mounting hole in the crossbrace.

4.Install the new seat upholstery onto the wheelchair. Refer to REPLACING SEAT UPHOLSTERY in PROCEDURE 5 of the Owners Manual, part number 1080737.

NOTE: Make sure to line up the mounting holes in the seat extension tubes with the new seat upholstery.

5.Install plug buttons into the ends of the seat extension tubes.

5

 

4

 

3

 

2

Locknuts

1

 

Washers

Hex Screws

Wheelchair Frame

FIGURE 2 - ADJUSTING BACK HEIGHT/

REPLACING BACK CANES

Washer

Phillips

Screws

Plug Button

Crossbrace

Seat Extension Tube

FIGURE 1 - ADJUSTING SEAT DEPTH

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Excel and P9000 E C I a L T E S R N I N GTable of Contents Specifications Specification SI F I C a T I O N S PowerRepair or Service Information Procedure General GuidelinesField Load Test Figure Using Hydrometer to Check Battery Cells Lead Acid FigureTroubleshooting Procedure Battery Charger Connector Digital VoltmeterCheck charging system Motor Testing FigureProcedure Troubleshooting Number of Floating BallsCap Pin Motor Connector OhmmeterCap Motor Tie Wrap Mounting Hole Locknuts Washer Hex Screws Replacing Back Upholstery FigureH O L S T E R Y Back Upholstery Washer Phillips ScrewA T M E Adjusting Seat Depth FigureAdjusting Back HEIGHT/ Replacing Back Canes Figure Seat Frame ProcedureRepositioning Mkiv Joystick Figure Procedure ElectronicsMkiv Joystick Mounting Tube Adjustment Lock Lever Preparing Mkiv Joystick for USE FigureReplacing Pneumatic TIRES/ Tubes Drive WHEELS/CASTERS REMOVING/INSTALLING Drive Wheels FigureWheels Procedure InstallingReplacing Forks Figure Procedure WheelsReplacing Casters Figure T T E R I E S Batteries ProcedureBattery Terminals/Posts U1 Battery Box Bottom Dual 22 NF T T E R Connecting Battery CablesDual U1 or Dual 22NF Battery Boxes Batteries Cover Battery Clamp Method Figures 4, 5Positive + Battery Terminal/Post Hex Nut Battery ClampR I E S Positive + Battery Terminal Post and Battery ClampRED Battery Unfolding/Folding Integrated Sling Seat Figure Refer to Battery Tray in this proce- dure of the manualAssembling Excel A I R SPush Brackets Pivot Link Crossbraces Adjusting FLIP-UP Removable FootboardFWD Wheelchairs Unfolding/Folding Captains Seat FigureHeight Figure Replacing Armrest Pads FigureReplacing Armrest Plate Figure Replacing Captains Seat Figure Steps 3 Steps 7Steps 5 Replacing Wiring HarnessFWD Wheelchairs Procedure Steps 2Limit Switch Phono Plug Body Phono Jack Adjusting Limit Switch FigureREMOVING/INSTALLING Shrouds Retaining Strap Installing Side Shrouds and FillersFiller Side Shroud Battery Box Battery Tray Phono Jack Phillips Screws Locknut16-18 or Changing Seat Width Integrated Sling Seats FigureReplacing Crossbraces Captains Seat Figure Spacer Washer Steps 6 Pivot Link Hex BoltsHex Bolts Steps 6 Crossbrace SpacerLocknutRequired Items When to Charge Batteries FigureDescription and Use of Battery Chargers Charging Batteries FigureReplacing Batteries INSTALLING/REMOVING Battery Boxes FigureRecommended Battery Types Cleaning Battery TerminalsChanging Width of Battery Tray Figure Battery TrayFolding Battery Tray for Transport Figure Unfolding Battery Tray for Use FigureInstalling Battery Tray Figure Replacing Right Battery Tray Hanger Bracket FigureRemoving Battery Tray Figure Spacer Hex Screw Footboard Mounting Bracket Battery Tray Hanger BracketReplacing Left Battery Tray Hanger Bracket Figure Repositioning Motors FigureRotate battery tray hanger bracket up Users Weight 201 to 250 LBSClutch Handle Steps 9 Replacing Clutch Handles FigureClutch Handle Pin Steps 317, 18 Steps 4Seat Rails Guides Assembling Power 9000 FigureRefer to INSTALLING/REMOV ING Footrests or Install Unfolding/Folding the WheelchairWait until charging is complete Battery Discharge IndicatorRWD Wheelchairs Retaining Strap Clip Connect the battery box retaining strap clip together14-15, 16-18 Battery Tray FigureChanging Seat Width Figure H a I R S Adjusting SEAT-TO-FLOOR HeightFrom Motors DisassemblyReassembly Phillips Screws To ControllerAlignment Hole Wheelchair Frame Support Tube Motor/Gearbox Underside of Motor Mount Plate Alignment Pin Long SocketMotor Mount PlateR R a N T Y Limited WarrantyChedworth Way
Top Page Image Contents