Invacare P9000 Battery Clamp Method Figures 4, 5, Positive + Battery Terminal/Post Hex Nut, Cover

Page 18

PROCEDURE 7

BATTERIES

B A T T E R I E S

Battery Clamp Method (FIGURES 4, 5 and 6).

WARNING

The battery clamp of the POSITIVE (+) battery terminal/post MUST be mounted in the position shown in FIGURE 5, otherwise the battery box top cannot be installed properly.

1.Perform one (1) of the following:

A.If the battery clamp of the POSITIVE (+) battery terminal/post is NOT mounted in the orientation shown in FIGURE 5, perform the following:

Loosenthehexnutthatsecuresthebatteryclamp tothePOSITIVE(+)batteryterminal/post.

CAUTION

When tightening the clamps, always use a box wrench. Pliers will “round off” the nuts. NEVER wiggle the battery terminal(s)/post(s) when tightening. The battery may become damaged.

RemovethebatteryclampfromthePOSITIVE

(+)battery terminal/post.

Reposition the battery clamp on the POSITIVE

(+)batteryterminal/postasshowninFIGURE4.

Securely tighten the hex nut that secures the battery clamp to the positive (+) battery terminal/post.

B.If the battery clamp on the POSITIVE (+) battery terminal/postispositionedasshowninFIGURE4, proceed to STEP 2.

CORRECT ORIENTATION OF THE POSITIVE (+) BATTERY TERMINAL/POST BATTERY CLAMP

POSITIVE (+) Battery Terminal/Post

(Note position of battery clamp)

Hex Nut

NEGATIVE (-) Battery

Terminal/Post and Battery Clamp

22NF Battery

FIGURE 4 - CONNECTING BATTERY CABLES - BATTERY CLAMP METHOD

2.Install battery clamp covers onto battery cables as follows (FIGURE 5):

A.REDbatteryclampcoverontoREDbatterycable.

B.BLACK battery clamp cover onto BLACK battery cable.

NOTE: Only one (1) battery cable and battery clamp cover are shown for clarity. Both battery clamp covers install in the same manner.

INSTALLING BATTERY CLAMP COVERS

Battery Clamp

Battery Cable

Cover

 

FIGURE 5 - CONNECTING BATTERY CABLES - BATTERY CLAMP METHOD

CAUTION

When connecting the battery cable/ring terminal(s) to the battery(ies) clamp(s), the battery cable(s) MUSt be connected in the position shown in DETAIL “A”, otherwise damage may occur to the battery cable and/or battery clamp covers.

3.Connect battery cable(s) to battery(ies) terminal(s)/ post(s) as follows (DETAIL “A”):

A.NEGATIVE (-) BLACK battery cable/ring terminal between the mounting plate and battery clamp of NEGATIVE (-) battery terminal/post.

B.POSITIVE(+)REDbatterycable/ringterminalbe- tween the mounting plate and battery clamp bat- tery clamp of POSITIVE (+) battery terminal/post.

4.Secure the battery cable(s)/ring terminal(s) to the bat- tery clamp(s), BLACK to NEGATIVE (-) and RED to POSITIVE (+), with exisitng hex screws. Securely Tighten. (DETAIL “A”)

5.Verify battery cable ring terminal(s) are correctly in- stalled and securely tightened.

6.Slide battery clamp covers down battery cables and onto battery terminals. (DETAIL “B”)

7.Secure each terminal cap in place with a tie-wrap (Use tie-wraps 11-1/2-inches long). (DETAIL “B”)

NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s).

8. Install the battery box top(s).

18

Image 18
Contents Excel and P9000 R N I N G E C I a L T E STable of Contents Specification S SpecificationsPower I F I C a T I O N SProcedure General Guidelines Repair or Service InformationBattery Charger Connector Digital Voltmeter Using Hydrometer to Check Battery Cells Lead Acid FigureTroubleshooting Procedure Field Load Test FigureNumber of Floating Balls Motor Testing FigureProcedure Troubleshooting Check charging systemPin Motor Connector Ohmmeter Cap MotorCap Back Upholstery Washer Phillips Screw Replacing Back Upholstery FigureH O L S T E R Y Tie Wrap Mounting Hole Locknuts Washer Hex ScrewsSeat Frame Procedure Adjusting Seat Depth FigureAdjusting Back HEIGHT/ Replacing Back Canes Figure A T M EPreparing Mkiv Joystick for USE Figure Procedure ElectronicsMkiv Joystick Mounting Tube Adjustment Lock Lever Repositioning Mkiv Joystick FigureInstalling REMOVING/INSTALLING Drive Wheels FigureWheels Procedure Replacing Pneumatic TIRES/ Tubes Drive WHEELS/CASTERSProcedure Wheels Replacing Casters FigureReplacing Forks Figure Batteries Procedure Battery Terminals/Posts U1 Battery Box Bottom Dual 22 NFT T E R I E S Connecting Battery Cables Dual U1 or Dual 22NF Battery BoxesT T E R Batteries Battery Clamp Battery Clamp Method Figures 4, 5Positive + Battery Terminal/Post Hex Nut CoverPositive + Battery Terminal Post and Battery Clamp RED BatteryR I E S A I R S Refer to Battery Tray in this proce- dure of the manualAssembling Excel Unfolding/Folding Integrated Sling Seat FigureUnfolding/Folding Captains Seat Figure Adjusting FLIP-UP Removable FootboardFWD Wheelchairs Push Brackets Pivot Link CrossbracesReplacing Armrest Pads Figure Replacing Armrest Plate FigureHeight Figure Replacing Captains Seat Figure Steps 7 Steps 3Steps 2 Replacing Wiring HarnessFWD Wheelchairs Procedure Steps 5Adjusting Limit Switch Figure Limit Switch Phono Plug Body Phono JackREMOVING/INSTALLING Shrouds Phillips Screws Locknut Installing Side Shrouds and FillersFiller Side Shroud Battery Box Battery Tray Phono Jack Retaining StrapChanging Seat Width Integrated Sling Seats Figure 16-18 orReplacing Crossbraces Captains Seat Figure SpacerLocknut Washer Steps 6 Pivot Link Hex BoltsHex Bolts Steps 6 Crossbrace SpacerCharging Batteries Figure When to Charge Batteries FigureDescription and Use of Battery Chargers Required ItemsCleaning Battery Terminals INSTALLING/REMOVING Battery Boxes FigureRecommended Battery Types Replacing BatteriesUnfolding Battery Tray for Use Figure Battery TrayFolding Battery Tray for Transport Figure Changing Width of Battery Tray FigureReplacing Right Battery Tray Hanger Bracket Figure Removing Battery Tray FigureInstalling Battery Tray Figure Repositioning Motors Figure Footboard Mounting Bracket Battery Tray Hanger BracketReplacing Left Battery Tray Hanger Bracket Figure Spacer Hex ScrewUsers Weight 201 to 250 LBS Rotate battery tray hanger bracket upPin Steps 3 Replacing Clutch Handles FigureClutch Handle Clutch Handle Steps 9Steps 4 17, 18Unfolding/Folding the Wheelchair Assembling Power 9000 FigureRefer to INSTALLING/REMOV ING Footrests or Install Seat Rails GuidesBattery Discharge Indicator RWD WheelchairsWait until charging is complete Connect the battery box retaining strap clip together Retaining Strap ClipBattery Tray Figure Changing Seat Width Figure14-15, 16-18 Adjusting SEAT-TO-FLOOR Height H a I R SPhillips Screws To Controller DisassemblyReassembly From MotorsPlate Underside of Motor Mount Plate Alignment Pin Long SocketMotor Mount Alignment Hole Wheelchair Frame Support Tube Motor/GearboxLimited Warranty R R a N T YChedworth Way